Nexa ZRT-106 Quick Manual Download Page 4

Parameter Number 

Size 

Range 

Default 

10 

1~48, means 30mins to 

24hrs 

8=4hrs 

Note

: When adjusting temperature by manual override, the unit will send Thermostat SetPoint 

Report to the gateway, but the mode will remain the same mode. 

Supported Thermostat Mode 

( from COMMAND CLASS THERMOSTAT_MODE_V3)

 

Mode 

Name 

Description 

0x00 

Off 

This mode is used to switch off the thermostat. 

0x01 

Heat   

This mode is used to use activate heating when the temperature is below 
the Heating (0x01) setpoint. 

0x0B 

Energy Heat 

This mode is used to use activate heating when the temperature is below 
the  Energy  Save  Heating  (0x0B)  setpoint.  The  Energy  Save  Heating 
(0x0B) setpoint is usually lower than the Heating (0x01) setpoint in order 
to save energy 

 

Thermostat SetPoint 

Mode 

Name 

Size 

Precision 

Scale 

Temp. Range 

0x01 

Heat   

1(one decimal place) 

0:Celsius 

Parameter 3&4 

0x0B 

Energy Heat 

1(one decimal place) 

0:Celsius 

Parameter 3&4 

 

Troubleshooting 
 

The table below lists the several steps involved when adding or removing the TRV from the Z-Wave 
network.

 

 

Action/Status 

Description 

Rings around the LCD 
display 

No node ID 

The Z-Wave Controller does not allocate a node 
ID to the unit. 

Blinks 2-second on, 
2-second off for 2 minutes 

Manual Inclusion 

1. Put the Z-Wave Controller into inclusion mode. 

 

2. Press the 

P

 button 3 times within 1.5 seconds to 

put the unit into inclusion mode. 

Exclusion 

1. Put the Z-Wave Controller into exclusion mode. 

 

2. Press the 

P

 button 3 times within 1.5 seconds to 

put the unit into exclusion mode. 

Factory Reset 
(This procedure 
should only be used 
when the controller is 
inoperable.) 

1. Press the 

P

 button 3 times within 1.5 seconds to 

put the unit into exclusion mode. 

 

2. Within 1 second of step 1, press the button 

P

 

again and hold for 5 seconds. 

 

3. Node ID is excluded. The device reverts to 

factory default state. 

2-second on, 2-second off 
For 2 minutes 

 Failed or successful results in including/excluding the ID can be viewed on the Z-Wave Controller. 

Note

: If you are connecting this unit to a Z-Wave Controller that utilizes the S2 security protocol, you may 

be asked by your controller to enter a 5 digit Device Specific Key (DSK) that is unique to each unit. This 
can be found in one of two places: 
- on the QR code label on the back of the unit 
- on the insert card inside the packaging 
 
 

The table below lists typical problems encountered:

 

Symptom 

Possible Cause 

Recommendation 

Cannot work 

Battery  is  not  fitted  properly  or 
run out of battery power. 

Check if batteries are fitted or replace a new 
battery. 

RF Reset 

Battery voltage is too low. 

To  make  device  boost  normally,  the  battery 
voltage must be DC2.8V. 

Cannot carry out 
inclusion 

and 

association 

Device  has  been  paired  to  other 
Z-Wave controller. 
 

1.  Perform  Exclusion  from  other  controller 
first  then  carry  out  inclusion  with  new 
controller. 
2.  Perform  Factory  Reset  on  device  and 
then carry out Inclusion with new controller 

Device is out of range. 

1. Relocate the controller closer to the unit. 
2.  Install  a  Z-Wave  repeater  such  as  smart 
plugs  or  other  AC  devices  that can  operate 
as a Repeater. 

 

Specifications 

Battery 

1.5V AA Battery*2 

Range 

Up to 50 meters line of sight 

Frequency Range 

EU: 868.42HMz, 

Type of valves 

M30 x 1.5 , Danfoss RAV/RA/RAVL type 

Temperature settings 

5

~35

, 0.5

  increments 

Specifications are subject to change without notice 

                                             

 

 
WARNING: 

 
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.   
Contact your local government for information regarding the collection systems available. 
If  electrical  appliances  are  disposed  of  in  landfills  or  dumps,  hazardous  substances  can  leak  into  the 
groundwater and get into the food chain, damaging your health and well-being. 
When  replacing  old  appliances  with  new  ones,  the  retailer  is  legally  obligated  to  take  back  your  old 
appliance for disposal at least for free of charge. 

 

Nexa Trading AB   
Datavägen 37B 
436 32 ASKIM - SWEDEN 
www.nexa.se   
[email protected]

 

Reviews: