background image

 

AeroVent

®

 Standard

 

ALWAYS wear appropriate personal protective equipment when operating the unit

!

 

 

 

AeroVent® Standard Manual / 4840.1117 

 

A respirator is required if the unit is NOT operated outdoors or in a well-ventilated area. 

Always consult your facility safety manager for particular safety protocols  

prior to operating this equipment. 

This unit is not intended for use with spray adhesives or expanding foam sealant products

 

 

 

 

 

 

 

 

 

PRECAUTIONARY WARNING! 

 

Please read and understand all operating instructions as detailed in 
this manual. Failure to follow specified instructions may result in 
equipment damage or serious injury to personnel, including death. 

 

Always refer to the current Product SDS for specific chemical 
handling and safety instructions prior to deflating aerosol cans. 

 

Liquids collected into drums and accompanying vapors may be 
highly flammable. Keep all waste collection containers away from 
heat, spark and flame 

 No Smoking near the unit or waste 

collection containers! 

 

Avoid static discharge. Ensure that the unit grounding cable is 
attached to a suitable grounding source such as metal water pipe or 
grounding rod prior to operation. 

 

Keep the collection container closed when not in use and kept in a 
cool, well-ventilated area away from ignition sources. 

 

Only operate unit out-of-doors or in a well ventilated area. 

 

Wear appropriate personal protective equipment and eye 
protection; avoid direct contact with aerosol can contents. 

 

CAUTION:

 Use of filters not specifically designed for the 

AeroVent®, aerosol can disposal systems may result in dangerous 
back pressure inside the recovery drum, resulting in equipment 
damage or serious injury to personnel, including death. 

 

ALWAYS refer to the Product SDS to check compatibility when 
multiple aerosols are co-mingled in the same collection drum. 

 

Caustics, Pesticides, Insecticides and White Metals should never 
be collected into a drum with other liquids and should be 
segregated into properly labeled, designated containers. Contact 
your waste handler or Facility Safety Manager for more 
information.

Summary of Contents for Aerovent Standard










Reviews: