Newland HR3290 Marlin User Manual Download Page 50

Page: 50 / 189

Enter Setup

** Exit Setup

Timeout between Decodes (Same Barcode)

Timeout between Decodes (Same Barcode) can avoid undesired rereading of same barcode in a given
period of time.

To enable/disable the Timeout between Decodes (Same Barcode), scan the appropriate barcode below.

Enable Timeout between Decodes:

Do not allow the scanner to re-read same barcode before the

timeout between decodes (same barcode) expires.

Disable Timeout between Decodes:

Allow the scanner to re-read same barcode.

Disable Timeout between Decodes

Enable Timeout between Decodes

The following parameter sets the timeout between decodes for same barcode. It is programmable in 1ms
increments from 0ms to 65,535ms. The default setting is 1,500ms.

To learn how to program this parameter, see

Appendix 5

Timeout between Decodes (Same Barcode)

Summary of Contents for HR3290 Marlin






























































































































































































Search results

Summary of Contents for HR3290 Marlin

Reviews:

Related manuals for HR3290 Marlin

Brands by name

Popular brands

Newland HR3290 Marlin, User Manual

Search results

Summary of Contents for HR3290 Marlin

Reviews:

Related manuals for HR3290 Marlin

Brands by name

Popular brands