Newland EM3296 Integration Manual Download Page 23 | Manualshive

Page: 23 / 24

background image

17

Chapter 5 Development Tools

EVK

The EVK is provided to help users to test and evaluate the EM3296, which contains beeper & beeper
driver circuit, LED & LED driver circuit, and trigger & reset buttons, TTL-232 to RS-232 converter &
TTL-232 to USB converter, RS-232 & USB interfaces, etc. The EM3296 can be connected to the EVK via
a 12-pin FFC cable type 1 (contacts on the same side). Either USB connection or RS-232 connection can
be used when connecting the EVK to a host device.

«
...
21
22
23
24
»

Summary of Contents for EM3296

























Reviews:

No comments

Related manuals for EM3296

Brand: Facit Pages: 51

OBID classic-pro ID CPR.03.20-CD

Brand: Feig Electronic Pages: 40

Brand: Contex Pages: 258

Brand: Hama Pages: 28

Brand: Inner Range Pages: 2

Brand: ViewSonic Pages: 128

Brand: Sensory Solutions Pages: 24

Brand: Shintaro Pages: 12

Brand: Godex Pages: 79

Brand: Diablotek Pages: 1

Brand: RIOTEC Pages: 3

Brand: RIOTEC Pages: 2

Brand: Leuze electronic Pages: 154

Brand: Intermec Pages: 8

Brand: Hand Held Products Pages: 2

Brand: Zebex Pages: 24

Brand: Zebex Pages: 44

Brand: Icarus Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands