Newland EM3296 Integration Manual Download Page 22 | Manualshive

Page: 22 / 24

background image

16

Good Read LED

The EM3296 provides a pin (LED, PIN 10) on the host interface connector that can be used by an external
driver circuit to drive an LED to indicate a Good Read status. When a good read occurs, the LED pin
produces a high level output and then the signal is back to a low level. This Good Read LED output is not
strong enough to drive an LED, so an LED driver circuit is needed.

The following Good Read LED driver circuit is provided for reference.

2N3904

Q8

R1 1K

LED

R3

1k

LED

D3

R2

10K

VDD

«
...
20
21
22
23
24
»

Summary of Contents for EM3296

























Reviews:

No comments

Related manuals for EM3296

Brand: TrekStor Pages: 86

QuickScan QBT2400

Brand: Datalogic Pages: 56

Infinea Tab 2 LPT

Brand: Infinite Peripherals Pages: 26

Brand: Salto Pages: 2

DRS-50 Translingual

Brand: SMART Pages: 12

SafezoneXID-500

Brand: LG CNS Pages: 33

Brand: Hama Pages: 24

Brand: Panasonic Pages: 11

Brand: Samsung Pages: 36

Brand: Technology Solutions Pages: 31

Brand: TrekStor Pages: 29

Brand: Blade Pages: 21

Brand: Shintaro Pages: 12

Brand: Optoelectronics Pages: 29

Brand: Ier Pages: 17

Brand: Sunstech Pages: 37

Brand: ARKSCAN Pages: 17

Brand: Opticon Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands