Newgrind Rhino RM250 Operator'S Manual Download Page 10

ing charge, plus a charge back for 

outbound freight charges if the original 

order was shipped prepaid. Returns are 

not accepted for any Products that are 

specifically manufactured to meet the 

buyer’s requirement of either specifica-

tions or quantity.

AGREEMENTS
These Terms and Conditions constitute the 

entire agreement between Seller and 

Purchaser as it relates to terms and condi-

tions of sale, and supersedes any and all 

prior oral or written agreements, 

correspondence, quotations or under-

standings heretofore in force between the 

parties relating to the subject matter 

hereof. There are no agreements between 

Seller and Purchaser with respect to the 

Product herein except those specifically 

set forth in and made part of these terms 

and conditions. Any additional terms, 

conditions and/or prices are rejected by 

Seller. These terms and conditions may be 

modified, cancelled or rescinded only by a 

written agreement of both parties execut-

ed by their duly authorized agents.

New Grind Inc.

103B- 81 Golden Dr 

Coquitlam

 BC

V3K 6R2

Telephone: 

1-888-467-0242

 

carissa

@newgrind.com 

www.newgrind.com

Summary of Contents for Rhino RM250

















Reviews: