New lift FST Manual Download Page 28

Page: 28 / 174

3 FST-Controller user interface
3.1 LC-Display and messages

FST_HB.EN04/03

PC-Card

PC:s0 m1 c0 f0 Mb005

State of holding

device

ASV: 0000000 P=[00]

The state of the holding device is decoded as follows:

Code

Description

No PC-Card inserted

PC-Card inserted – card type not detected

PC-Card inserted – card type detected / card OK

PC-Card inserted – card type not detected / error

PC-Card memory type unknown

Card type: static RAM

Card type: flash memory

CIS memory: no CIS found

CIS status: CIS OK

Flash type: PC-Card unknown / unusable

Flash type: AMD A28F040 – 512kB memory module

Flash type: INTEL I28f016 – 2MB memory module

Size of memory storage in 0.1 MB steps

Bit

Setting

Description

ASV: .......

(right)

active

Pump for bolt control ON

active

Valve “extend bolt” activated

active

Valve “retract bolt” activated

active

Limit switch “bolt extended” active

active

Limit switch “bolt retracted” active

active

Input “car bottomed” active

(left)

active

Input “re-pump” active

Number

Code

Description

P=[..]

1 (right)

Standstill

1 (right)

Main contactors ON, waiting for star-delta start up

1 (right)

Lift car (approx. 30mm)

1 (right)

Motor run-on active

1 (right)

Wait for bolt to extend or retract

1 (right)

Bolt extended or retracted completely

1 (right)

Wait for input “car bottomed”

1 (right)

Delay after stop

2 (left)

No bolt movement

2 (left)

Bolts are retracting

2 (left)

Bolts are extending

Summary of Contents for FST















































































































































































Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands

New lift FST, Manual

Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands