New lift FST Manual Download Page 135 | Manualshive

Page: 135 / 174

background image

1 Menu tree

1.5 MAIN MENU – Positioning

FST_HB.EN04/03

133

Global –

Encoder type

Type of shaft positioning:

-

Absolute: Linear positioning with absolute value encoder
and tooth belt.

-

Incremt.: Incremental positioning with incremental encoder
on motor or speed limiter.

Absolute
Incremt.

Global –

Max.Floor

Number of floors of the lift system, starting with zero.
(Example: 8 floors –> Setting = 7)

0 ... 63

Global –

Crawl Distance

Length of desired crawling distance. The set value is added to
the approach distance for each speed (V1 … V8) determined
during the calibration drive.
(Setting = 0 –> Direct approach)

-500 ... 500 mm

Global –

Insp.FAST

Measured deceleration distance of fast inspection speed. The
set value shows the deceleration points of the fast inspection
drive before the levelling position of the top and bottom
landings. If this distance is set too short the car can run into
the limit switch. This value should always be checked after a
calibration drive and extended if necessary.

0 ... 5000 mm

Global –

Insp.UP

Measured deceleration distance of slow inspection speed
when moving up. The set value shows the switch-off point of
the inspection drive before the levelling position of the top
landing. If this distance is set too short the car can run into the
limit switch. This value should always be checked after a
calibration drive and extended if necessary.

-5000 ... 5000 mm

Global –

Insp.DOWN

Measured deceleration distance of slow inspection speed
when moving down. The set value shows the switch-off point
of the inspection drive before the levelling position of the
bottom landing. If this distance is set too short the car can run
into the limit switch. This value should always be checked after
a calibration drive and extended if necessary.

-5000 ... 5000 mm

Global –

ZoneB Output

-

Output of the internally generated encoder-B signal (also
see “Output encoder-B simulation” on page 42). The output
is 0V if the car is outside the door zone.

YES
NO

Global –

ZoneB Out.Inv.

Inverts the output of the internally generated encoder-B signal
(also see “Output encoder-B simulation” on page 42).

-

YES: The output is 0V if the car is in the door zone.

-

NO: The output is 0V if the car is outside the door zone.

YES
NO

Global –

Virt.Zone

Determines whether the values set in

Positioning –

Floor – Zone Sw.UP/DOWN

are real or virtual zone

signals. With linear positioning this parameter should always
be set to

YES

, with incremental positioning always to

NO

!

Incorrect setting of this value can lead to problems with door
control and levelling positions after adjusting the levelling!

YES
NO

Relevel. Limits –

Limit UP ON

The relevelling when moving up starts at the set distance
between car and levelling position (see “Relevel. Limits” on
page 138).

0 ... 2500 mm

Relevel. Limits –

Limit UP OFF

The relevelling when moving up stops at the set distance
between car and levelling position (see “Relevel. Limits” on
page 138).

0 ... 2500 mm

Relevel. Limits –

Limit DN ON

The relevelling when moving down starts at the set distance
between car and levelling position (see “Relevel. Limits” on
page 138).

0 ... 2500 mm

Menu item

Description

Setting range

«
...
133
134
135
136
137
...
»

Summary of Contents for FST















































































































































































Reviews:

No comments

Related manuals for FST

Brand: Eaton Pages: 50

Concord express

Brand: GE Pages: 3

Brand: Abicor Binzel Pages: 8

Brand: B&G Pages: 2

Brand: B&K Pages: 9

Brand: Daikin Pages: 38

Brand: Daikin Pages: 2

Brand: Daikin Pages: 148

Brand: Daikin Pages: 12

Brand: Daktronics Pages: 52

Brand: Waeco Pages: 20

Brand: Z-Wave Pages: 56

Brand: tams elektronik Pages: 60

Brand: Samson Pages: 8

Brand: Samson Pages: 60

Brand: Samson Pages: 40

NOVASTAT EL DIGITAL

Brand: Taconova Pages: 7

Optidrive Elevator

Brand: Invertek Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands