New lift FST-2XT MRL Short Instructions Download Page 30

Page: 30 / 32

Error list

Update-Backup-Analysis FST-2XT FST-2XTs

9.3

Error messages

Error message

Possible cause

Error correction

USBStick UNKNOWN

USB stick not detected by the
FST

USB stick defective

Incorrectly formatted USB stick

Use the controller fuse to
switch the control system OFF
and ON

Change USB stick

RECORD TRANSFER ERR!

Recording performed incom-
pletely or incorrectly

Recording was interrupted

Repeat recording procedure

DIR NOT FOUND!

Capitalisation of file name not

correct

Folder not present

Rename folder on USB stick

Create folder on USB stick

UNZIP FAILED

The file with extension *.tar was

already extracted into folder

update

Copy file

FST-2XT_update_

V2.000-xxxx.tar

to the USB

stick again and repeat the
update

UNKNOWN DIR ERROR

Folder not detected by the FST

Use the controller fuse to
switch the control system OFF
and ON

Summary of Contents for FST-2XT MRL

































Search results

Summary of Contents for FST-2XT MRL

Reviews:

Related manuals for FST-2XT MRL

Brands by name

Popular brands

New lift FST-2XT MRL, Short Instructions

Search results

Summary of Contents for FST-2XT MRL

Reviews:

Related manuals for FST-2XT MRL

Brands by name

Popular brands