manualshive.com logo in svg

New Home NH7, Service Manual

Share
Download
New Home NH7 Service Manual Download Page 20

18

ADJUSTMENT OF RIGHT HAND LINE TACK WIDTH AND CAM FOLLOWER RELEASE 
AMOUNT

*  THE WIDTH OF THE LEFT AND RIGHT SIDE LINE TACK OF BUTTONHOLE SHOULD BE
     EQUAL.  IF THERE  IS  LARGE  DIFFERENCE  BETWEEN  LEFT  AND  RIGHT  LINE TACK 

WIDTH,

 

THE CAM FOLLOWER MAY BE HINDERED WITH THE ZIGZAG CAM BLOCK WHEN 

YOU TURN THE PATTERN SELECTOR DIAL.

1.  SEW A BUTTONHOLE AND CHECK THE DIFFERENCE IN BOTH LINE TACK WIDTHS.
2.  REMOVE THE FRONT COVER (SEE PAGE 6).
3.  ADJUST THE LINE TACK WIDTH BY TURNING THE ADJUSTING SCREW.

*  THE RIGHT SIDE OF THE LINE TACK IS FIXED SO THE ADJUSTMENT SHOULD BE  

 

DONE ON THE LEFT SIDE LINE TACK.

     IF THE LEFT SIDE LINE TACK IS WIDER THAN THE RIGHT SIDE:
     TURN THE ADJUSTING SCREW IN THE DIRECTION OF “A”
     IF THE RIGHT SIDE LINE TACK IS NARROWER THAN THE LEFT SIDE:
     TURN THE ADJUSTING SCREW IN THE DIRECTION OF

 

“B”

.

MECHANICAL ADJUSTMENT

"B"

"A"

ADJUSTING SCREW

LEFT SIDE LINE
TACK WIDTH

RIGHT SIDE LINE
TACK WIDTH

Summary of Contents for NH7























Reviews:

No comments

Brands by name

Popular brands

Load more brands