manualshive.com logo in svg

New Home NH7, Service Manual

Share
Download
New Home NH7 Service Manual Download Page 15

13

CLEARANCE BETWEEN NEEDLE AND HOOK (NO.2)

 

TO CHECK:

USE THIS ADJUSTMENT NO.2 WHEN ADJUSTMENT NO.1 CAN NOT BE USED.
THE CLEARANCE BETWEEN NEEDLE AND SHUTTLE RACE SHOULD BE –0.05-0.10MM.

 

ADJUSTMENT PROCEDURE:

1. 

SET THE PATTERN SELECTOR DIAL AT MAXIMUM SIGZAG WIDTH, AND TURN THE    

 

HANDWHEEL TOWARD YOU TO ERING THE NEEDLE TO THE LEFT NEEDLE POSITION.

2. 

OPEN THE SHUTTLE COVER AND LOOSEN THE LOWER SHAFT BUSHING    

 

 

(FRONT) SETSCREW "A". THEN SLIDE THE LOWER SHAFT TO THE RIGHT  

 

 

 

SIDE SLIGHTLY (APPROXIMATELY 0.5 MM) NOT TO DISENGAGE THE GEARS,   

 

 

AND TIGHTEN THE SCREW TEMPORARY.

3. 

LOOSEN THE SCREWS "B" (2 PCS) THROUGH THE HOLES IN THE REAR  

 

 

 

COVER, AND SLIGHTLY MOVE THE SHUTTLE BODY UP OR DOWN TO ADJUST  

 

 

THE CLEARANCE BETWEEN NEEDLE AND SHUTTLE HOOK TO –0.05 – 0.10MM,  

 

 

AND TIGHTEN THE SCREWS "B" TEMPORARY.

4. 

TURN THE HANDWHEEL TO CHECK THE CLEARANCE BETWEEN SHUTTLE RACE    

 

SPRING AND NEEDLE IN LEFT AND RIGHT POSITIONS. IF THE CLEARANCE IS NOT   

 

EQUAL, ADJUST IT BY TURNING THE SHUTTLE RACE BODY.

5. 

TIGHTEN THE TWO SHUTTLE RACE SETSCREWS "B" (2 PCS).

6. 

LOOSEN THE SETSCREW ON LOWER SHAFT BUSHING AND SLIDE THE  

 

 

 

GEAR BACK TO THE ORIGINAL POSITION WHILE ADJUSTING THE BACKLASH.

7. 

TIGHTEN THE SCREW A FIRMLY.

NOTE:  THE BACKLASH PLAY SHOULD BE LESS THAN 0.3MM AND LOWER SHAFT TURNS  

 

 

   SMOOTHLY.

AFTER THE ADJUSTMENT, CHECK THE HOOK TIMING.

MECHANICAL ADJUSTMENT

SETSCREW "A"

–0.05 – 0.10MM

CLEARANCE SHOULD BE EQUAL

SHUTTLE RACE SPRING

NEEDLE

LOWER SHAFT BUSHING
(FRONT)

SHUTTLE RACE
SETSCREW "B"
(2 PCS.)

HOLES  IN  THE 
REAR COVER

Summary of Contents for NH7























Reviews:

No comments

Brands by name

Popular brands

Load more brands