New Holland CR8.90 Service Manual Download Page 76 | Manualshive

Page: 76 / 81

background image

Engine - Air cleaners and lines

7. If the element is soiled with oil or soot, it is possible to

dip the filter in and out of a bucket containing 75 grams
(0.165 lbs.) of non-foamy detergent and

10 l

(

2.6 US

gal

) and lukewarm water. Once the filter appears to

be clean rinse the filter off lightly with clean water to
remove the soap.

NOTE:

Do not allow water to get into the inside of the filter.

Always keep the open end up while dipping.

NOTE:

Do not use high pressure water to clean the filter

when rinsing. Use only low pressure tap water.

NOTE:

Never use Gasoline or Diesel fuel to clean the Air

filter element.

8. Every time the element is cleaned, it should be exam-

ined for holes and cracks by holding an electric light
bulb inside the element and looking through it. If any
damage is noted, discard the element and fit a new one.

9. Replace the element after cleaning three times or once

a year, whichever comes first.

10. When fitting, make sure the element is seated properly

and the sealing is in good condition.

11. A safety element

(1)

is fitted as an additional security

to prevent dust from entering the engine when replac-
ing the standard element. The safety element should
normally not be cleaned. Replace the safety element
when the primary element is changed.

NOTE:

Illustration is for reference only. Part may look dif-

ferent, depending on model.

_47865347 25/04/2015

10.2 [10.202] / 12

«
...
74
75
76
77
78
...
»

Summary of Contents for CR8.90


















































































Reviews:

No comments

Related manuals for CR8.90

Brand: Falcon Pages: 52

Brand: Kapriol Pages: 32

Brand: JABO Pages: 4

Brand: DAKO Pages: 25

Brand: 3M ESPE Pages: 50

Brand: VACGEN Pages: 13

Brand: Idmed Pages: 2

Brand: jablotron Pages: 2

TRAKTOR KONTROL S4

Brand: Native Instruments Pages: 86

Brand: Native Instruments Pages: 245

Brand: Safavieh Pages: 2

Brand: Vendlet Pages: 2

Brand: Yetter Pages: 24

Brand: Yetter Pages: 32

Brand: KaVo Pages: 70

Brand: GreenTec Pages: 66

Brand: Slick Pages: 2

Sedeo Lite Q700M

Brand: Quickie Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands