background image

4

Carefully place the ar

b

or

 / arch

 on its side. Continue to 

insert the

 

mounting extensions

 

in

to the 

b

ottom of the 

posts until they touch

 

the 

b

ottom rail on the side panel. 

STEP FOUR

 

Arbor 

/ Arch 

Installation 

2

A

 - Install Ground Stakes

www.newenglandarbors.com 

www.newenglandarbors.co.uk

2

North America Toll Free Phone: 1 800 282 9346 

United Kingdom Tel: (44) 2038 687160 

A

1

1

2

Arbors  must  be  well  secured  to  prevent  tipping  over  from  wind  load 
etc.  We  have  provided  four  ground 

mounting  extensions 

for 

securing  the  arbor  either  into  the  ground  or  a  concrete  footing.    In 
some  cases  it  may  be  acceptable  to  secure  the  arbor  to  an  existing 
structure such as a fence post.  If you  are  installing  your  arbor  on 
concrete  or  a  deck,  see  your  hardware    store  for  the  appropriate 
galvanized bracketing hardware. 

1

8

" (46 cm)

6

"

(15 cm)

Move the ar

b

or to its final location (you will need a helper). 

W

hen 

you are satisfied with the location, mark the positions of the posts, 

then move the ar

b

or aside and lay it carefully on its side.

 

E

x

cavate 4 

holes appro

x 10 

in. 

 (24 cm) 

deep.  Carefully move the ar

b

or

 

b

ack into 

position and level it 

b

oth vertically and horizontally.

Backfill the holes with the e

x

cavated soil to cover the anchors.

1

2

Complete B #1 a

b

ove, with the e

x

ception of e

x

cavating the holes at 

leas

t 6

in. 

(15 cm) 

wide 

x 18

in. 

(46 cm) 

deep.  Fill holes with wet cement 

within 3in. 

(8 cm) 

of your grade (yo

u will need 2 bag

s of pre-m

ix

 concrete 

- purchase separately).  Carefully move the ar

b

or

 b

ack into position.

1

2

Using two screws per post, fasten the 

mounting 

extensions

 

in

to

 

post as shown aside.

B

 - Into Earth Without Concrete Footing

C

 - Into Earth With Concrete Footing

Support the ar

bor plumb and l

evel ov

er the holes with b

ricks

,

 

stones o

r blo

cks of wood under the 

b

ottom rail of the side panel.  

The post 

b

ottoms should insert themselves appro

x 1/2i

n.

 (1 cm)

 

into the concrete.

Optional

If you plan on attaching a fence or 

b

ench to the ar

b

or, or in the 

event of e

x

treme wind conditions we would not recommend 

using the ground anchors provided.  Consider purchasing pressure  

treated lum

b

er and trimming it down to 

3 1/4in. 

(8 cm) 

wide

 and 

cutting it int

o 36in

(91 cm) 

lengths. Insert into the 

b

ottom of all 

four posts until  they hit the 

b

ottom horizontal rail on the side 

panel.  Fasten  accordingly with screws and install either directly 

into the ground  or into a concrete footing. 

B

10

(25 cm)

4

"

(10 cm)

C

Summary of Contents for The Florence

Page 1: ...tool or Short Ladder Shovel General Information Read Instructions through carefully before beginning assembly When assembling components place on a non abrasive surface i e shipping box to avoid scratching We recommend an area approx 10ft x 8ft 3mx2 5m for unobstructed assembling You should not need to use excessive force when assembling components ASSEMBLY INSTRUCTIONS The Florence Arbor Arch 15 ...

Page 2: ...ges on either side of the bottom of the insert This will connect the bottom of the arches to the insert Seal the bottom hole on the keystone by inserting the bottom plate as provided Install the top cap on the arch keystone Push down firmly so the cap locks into position Repeat for other arch Insert arch rafters 6 into the holes on the arches until they bottom out inside the arches There are locki...

Page 3: ...e that there are Left and Right side posts as indicated with the L and R at the top of the respective posts Repeat for other side panel 1 Assemble the Side Panels 2 3 4 5 6 7 1 2 3 4 6 Set out one side panel Insert the assembled arch through the holes at the top of the posts Do the same for the other side panel You will need a helper Adjust the opening width to 42in between the posts arbor allows ...

Page 4: ... into position and level it both vertically and horizontally Backfill the holes with the excavated soil to cover the anchors 1 2 Complete B 1 above with the exception of excavating the holes at least 6in 15 cm wide x 18in 46 cm deep Fill holes with wet cement within 3in 8cm of your grade you will need 2 bags of pre mix concrete purchase separately Carefully move the arbor back into position 1 2 Us...

Reviews: