manualshive.com logo in svg

New England Arbors The Devonshire Arbor, Assembly Instructions Manual, Page: 6 / 7

Share
Download
New England Arbors The Devonshire Arbor Assembly Instructions Manual Download Page 6

STEP FOUR

Slip the trim cap over the post and slide down about 12”.  If you purchased the Trim Kit

,

 slip the second trim cap as well as the

base moldings. No glue is required for this step.

Attach the Trim Pieces

1

www.newenglandarbors.com 

6

The Devonshire Arbor

Included in the Trim Kit

Carry the side panels to the final location of the arbor and
Excavate four holes approx 36 in. (91.4 cm.) deep

,

 12 in. in diameter. 

The spacing of the holes should be as per image aside.

Carefully move the side panels into the excavated holes.

Run a 2” - 3” long bead of glue on the ribbed flanged of the
arch couplers as shown. 

STEP FIVE

Install The Arbor

2

3

2

3

Into Earth with Concrete Footing

Arbors must be well secured to prevent tipping over from
wind load, etc.  

1

36 in.

91.4 cm.

12 in.

30.5 cm

.

(Measurements shown are inside to inside of posts)

49 in.

124.5 cm.

24.5in.

62.2 cm.

Summary of Contents for The Devonshire Arbor








Reviews:

No comments