background image

INTRODUCTION 

 

This instruction manual will help you obtain a safe, efficient, dependable installation for your appliance 
and vent system.  Please read and understand these instructions before beginning your installation. 
 
The model DV23ZC is a sealed combustion, air circulating gas appliance designed for residential and 
mobile home applications.  The appliance must be installed with Dura-Vent GS vent system that is 
routed to outside atmosphere.  It is also listed for bedroom installations. 
 
This appliance is designed to operate on natural or propane gas.   A millivolt gas control valve with piezo 
ignition system provides safe, efficient operation.  No external electrical power is required to operate the 
gas valve and burner.  120VAC is required to operate the room air fan. 
 
This appliance complies with National Safety Standards and is tested and listed by (ITS) Intertek Testing 
Services (Warnock Hersey)  to 

ANSI Z21.88-2002 and CSA 2.33-2002 

ISA  CAN/CGA-2.17-M91-

Appliance for use at high altitudes.  Installation must conform to local codes.  In the absence of local 
codes, installation must comply with the current 

National Fuel Gas Code, ANSI Z223.1/NFPA54

.

.  

(In Canada, installation must comply with the current 

CAN-1B149 

installation code.) 

 

Approved for manufactured (Mobile) home installation.

  For mobile housing, Title 24 CFR, Part 

3280 or when such a standard is not applicable, the standard for manufactured home installation, ANSI /
NCBS A225.1 or standard for gas  equipped recreation vehicles and mobile housing, CSA Z240.4. 

DO NOT ATTEMPT TO ALTER OR MODIFY THE CONSTRUCTION OF THE 
APPLIANCE OR ITS COMPONENTS.  ANY MODIFICATION OR ALTERATION 
MAY VOID THE WARRANTY, CERTIFICATION AND LISTINGS OF THIS UNIT. 
 

SPECIFICATIONS - MODEL DV23ZC 
 
GAS:   

 

 

    NAT. 

 

 

 

     L.P.  

 HIGH 

FIRE 

 

  

22,000 

BTU 

   22,000 

BTU 

 LOW 

FIRE 

 

  

14,000 

BTU 

   17,600 

BTU 

 
GAS INLET PRESSURE: 

    NAT. 

 

 

 

     L.P. 

 

MAX. INPUT  

10.5" W.C. 

 

 

 

   14.0" W.C. 

 

MIN.  INPUT  

*5.0" W.C. 

 

 

 

   10.5" W.C.    

 *5.0" W.C. is minimum inlet gas supply pressure for the purpose of input adjustment. 
 
MANIFOLD PRESSURE:       NAT.  

 

 

 

     L.P. 

    3.5" 

W.C. 

   10.0" 

W.C. 

 
STEADY 

STATE 

EFFICIENCY: 

    

    NATURAL 

GAS 

77.10%    

    L.P. 

GAS 

 77.10% 

 

 

 

FLUE VENT   

 

4" INNER,  6" OUTER; DURA-VENT MODEL GS 

 
SAFETY 

 

 

AGA CERTIFIED PILOT GENERATOR, MILLIVOLT  

    SYSTEM 

ACTIVATED 

WITH SWITCH OR THERMOSTAT. 

 

Summary of Contents for DV23ZC


































Reviews: