background image

MOD 

When turned up, this introduces a 

random modulation to the 

frequency of each voice, but 

unlike common LFOs this does not 
vary slowly over time. Rather, a 

new deviation value is chosen for 

each cycle of the waveform. The 

amount of deviation is controlled 

with this knob. Turned fully 

counter-clockwise, there is no 

modulation. 

FILTER 

This  is a low-pass filter that 

takes off some of the high range 

frequencies when turned down. You 

might want to leave this knob 

turned fully up by default and 

turn down as desired when the 

harshness introduced by the 

distortion or excessive filter 

feedback is too high for your 

taste. 

VOLUME 

Much to the user’s surprise, this 

knob controls the overall volume 

of the sound. 

It can also be used 

to conjure up 

various ethereal 

entities. The exact 

mode of operation 

is left as an 

exercise to the 

user. 

SCRATCH 

This controls Elmyra’s nasty 

distortion. The circuit is built 

in such a way that a slight 

amount of distortion is present 

at all times, even if this is 

turned down. Turn it up to 

increase the nastiness. 

BITE 

This switch, when in position 2, 

will add high overtones and noise 
to the distortion. If the SCRATCH 
knob is turned down, it will have 

no perceivable effect. 

Summary of Contents for ELMYRA V1.3










Reviews: