Neumann TLM 102 Operating Manual Download Page 5

9

9

EN

The microphone has a balanced, transformerless 
output. The 3-pin XLR connector has the following 
standard pin assignments:

Pin 1:  0 V/Ground
Pin 2:  Modulation (+phase)
Pin 3:  Modulation (–phase)

1)

  All values are for non-condensing humidity.

The values are valid for clean and well-looked-aft er 
microphones or microphone capsules, respectively. Any 
kind of pollution of capsules and membranes may restrict 
the said values.

2)

  at 1 kHz into 1 kohm rated load impedance.

3)

  re  94 dB SPL

4)

   according to IEC 60268-1; 

CCIR-weighting acccording to CCIR 468-3, quasi peak; 
A-weighting according to IEC 61672-1, RMS

5)

   THD of microphone amplifi er at an input voltage equivalent 

to the capsule output at the specifi ed SPL. 

6)

   according to IEC 61938

9.   Selected Accessories* 

(see photos in appendix) 

Elastic Suspensions

EA 1 ..........................ni ..................Cat.  No.  008449
EA 1 mt .....................blk ................Cat. No.  008450

Auditorium Hanger

MNV 87 ....................ni ..................Cat.  No.  006804
MNV 87 mt ...............blk ................Cat. No.  006806

Stand Mounts, Misc. Mechanical Adapters

DS 120  .....................blk ................Cat.  No.  007343
SG 2..........................blk ................Cat. No.  008636

Table and Floor Stands

MF 4 .........................blk ................Cat.  No.  007337

Foam Windscreens

WS 2 .........................blk ................Cat.  No.  008637

Popscreen

PS 15  .......................blk ................Cat. No.  008472

Power Supply

N 248 .......................blk ................Cat. No.  008537

Connecting Cables

IC 3 mt  ....................blk ................Cat. No.  006543
IC 4 ...........................ni ..................Cat.  No.  006547
IC 4 mt .....................blk ................Cat. No.  006557

Adapter Cables

AC 25  .............................................Cat. No.  006600

Meaning of color codes:
ni = nickel, blk = black, gry = grey

*   Detailed descriptions and additional articles can be found 

in our accessories catalog or at: www.neumann.com

Summary of Contents for TLM 102









Reviews: