Neumann.Berlin KMR 81 i Operating Instructions Manual Download Page 3

4

5

KMR 81 i

phones  as  well  as  the  modulation  conductors  of
tube-equipped condenser microphones without the
need to switch off the dc supply voltage.

No harm is done even if a Neumann phantom pow-
er  supply  is  connected  to  the  inputs  of  micro-
phones which are phantom powered from another
source.

2.2 ac Supply Operation

All  P48  power  supplies  in  accordance  with
IEC 1938 which provide at least 1 mA per channel,
are suitable for powering the microphones.

The  Neumann  P48  power  supply  unit  bears  the
designation  N 248.  It  is  designed  to  power  two
mono condenser microphones or one stereo micro-
phone at 48 V ± 1 V, max. 2 x 6 mA (see also Neu-
mann bulletin no. 68832: ”Phantom 48 VDC Pow-
er Supplies“).

The assignment of the microphone terminals and
the modulation polarity at the power supply out-
put are identical to those at the microphone.

The N 248 supplies one stereo microphone, or two
mono condenser microphones with 48 V phantom
power (P48). All connectors are of XLR 3 type. The
audio signal outputs are DC-free.

Three  versions  are  available:

N 248 EU ............ blk ............. Cat. No. 08537
N 248 US ............ blk ............. Cat. No. 08538
N 248 UK ............ blk ............. Cat. No. 08539

2.3 Battery Powering

If  a  mains  power  source  is  not  available,  power
can be supplied by one of the battery units

BS 48 i .................................... Cat. No. 06494
(for one microphone)

BS 48 i-2 ................................. Cat. No. 06496
(for two microphones)

Both units deliver 48 V ± 1 V, at 5 mA maximum,
and  are  powered  by  a  9-volt  monobloc  battery
Type  IEC 6 F 22.

The BS 48 i-2 is equipped with 5-pin XLR connec-
tors, the BS 48 i with 3-pin XLR connectors.

(See Neumann bulletin 68832... “Phantom 48 VDC
Power Supplies”.)

The 3-pin XLR connector has the following pin as-
signments:

Pin 1: 0 V/ground

Pin 2: Modulation (+phase)

Pin 3: Modulation (–phase)

1.2 Microphone Cables

The  following  cables  are  available  for  the
KMR 81 i microphone:

IC 3 mt ................ blk ............. Cat. No. 06543

Microphone  cable  with  double  twist  (double  he-
lix)  braiding  as  shield.  Ø 5 mm,  length  10  m.
XLR 3 connectors, matte black.

IC 31 mt (5 m) .... blk ............. Cat. No. 06570

Microphone  cable  with  double  twist  (double  he-
lix)  braiding  as  shield.  Textile-braided  to  avoid
frictional  noise  due  to  the  handling  of  booms  or
plastic  leadings  (for  example  in  windscreens).
Ø 4,5 mm,  length  5  m.  XLR  3  connectors,  matte
black.

AC 25 (0.3 m) ......................... Cat. No. 06600

Adapter cable with XLR 3 M connector and unbal-
anced 6.3 mm mono jack. It is used to connect 3-
pin XLR outputs of power supplies to units with a
6.3 mm  monojack  input.  Designed  for  all  micro-
phones, excluding KM 100 System and GFM 132.

Special cable lengths can be made to order.

2.

Power Supply

2.1 Phantom Powering

The KMR 81 i is phantom powered at 48 V (P48, IEC
1938).

With phantom powering the dc from the positive
supply terminal is divided via two identical resis-
tors, one half of the dc flowing through each au-
dio (modulation) conductor to the microphone, and
returning  to  the  voltage  source  via  the  cable
shield.  Phantom  powering  provides  a  fully  com-
patible connecting system, since no potential dif-
ferences exist between the two audio conductors.
Studio outlets so powered will therefore also ac-
cept  dynamic  microphones  and  ribbon  micro-

Der  3-polige  XLR-Steckverbinder  hat  folgende
Belegung:

Pin 1: 0 V/Masse

Pin 2: Modulation (+Phase)

Pin 3: Modulation (–Phase)

1.2 Mikrophonkabel

Für das KMR 81 i stehen folgende Kabel zur Ver-
fügung:

IC 3 mt ............... sw ............ Best.-Nr. 06543

Mikrophonkabel mit Doppeldrallumspinnung als
Abschirmung. Ø 5 mm, Länge 10 m. XLR 3 Steck-
verbinder, schwarzmatt.

IC 31 mt  (5 m) ... sw ............ Best.-Nr. 06570

Mikrophonkabel mit Doppeldrallumspinnung als
Abschirmung. Textilumsponnen, zur Vermeidung
von Reibgeräuschen bei der Verwendung an Mi-
krophonangel  oder  Windschutzkorb.  Ø 4,5 mm,
Länge 5 m. XLR 3 Steckverbinder, schwarzmatt.

AC 25  (0,3 m) ...................... Best.-Nr. 06600

Adapterkabel mit XLR 3 F-Buchse und 6,3 mm Mo-
noklinkenstecker,  unsymmetrisch,  für  den  An-
schluss des 3-poligen XLR-Ausganges eines Spei-
segerätes  an  Geräte  mit  6,3 mm  Monoklinken-
buchse. Für alle Mikrophone mit Ausnahme der
Ausgangsstufe KM 100 und des GFM 132.

Andere Kabellängen sind auf Wunsch lieferbar.

2.

Stromversorgung

2.1 Phantomspeisung

Das KMR 81 i wird mit 48 V phantomgespeist (P48,
IEC 1938).

Bei der Phantomspeisung fließt der Speisestrom
vom positiven Pol der Spannungsquelle über die
elektrische  Mitte  der  beiden  Modulationsadern
zum Mikrophon. Er wird hierzu über zwei gleich-
große Widerstände beiden Tonadern gleichsinnig
zugeführt. Die Rückleitung des Gleichstroms er-
folgt über den Kabelschirm. Zwischen beiden Mo-
dulationsadern besteht also keine Potentialdiffe-
renz. Daher ist mit der Phantomspeisung eine kom-
patible Anschlusstechnik möglich:

Auf die Anschlussdosen können wahlweise auch
dynamische Mikrophone oder Bändchenmikropho-
ne sowie die Modulationskabel röhrenbestückter
Kondensatormikrophone geschaltet werden, ohne
dass die Speisegleichspannung abgeschaltet wer-
den muss.

Der Ausgang eines Neumann-Phantomspeisegerä-
tes darf auch auf bereits anderweitig phantomge-
speiste Mikrophoneingänge gesteckt werden.

2.2 Betrieb mit Netzgeräten

Für die Stromversorgung sind alle P48-Netzgerä-
te geeignet, die mindestens 1 mA je Kanal abge-
ben.

Das Neumann P48-Netzgerät hat die Bezeichnung
N 248. Es ist zur Stromversorgung zweier Mono-
Kondensatormikrophone oder eines Stereomikro-
phons mit 48 V ± 1 V, maximal 2 x 6 mA, geeignet
(siehe auch Neumann-Druckschrift 68832: „48 V-
Phantomspeisegeräte“).

Die Zuordnung der Mikrophonanschlüsse und die
Polarität  der  Modulationsadern  ist  am  Ausgang
des Speisegerätes die gleiche wie am Mikrophon.

Das Netzgerät N 248 versorgt ein oder zwei Mikro-
phone mit 48 V-Phantomspeisung P48. Alle An-
schlüsse mit XLR 3-Flanschdosen. Die Modulati-
onsausgänge sind gleichspannungsfrei.

Das Gerät ist in drei Ausführungen erhältlich:

N 248 EU ............ sw ............ Best.-Nr. 08537
N 248 US ............ sw ............ Best.-Nr. 08538
N 248 UK ............ sw ............ Best.-Nr. 08539

2.3 Batteriespeisung

Steht keine Netzspannung zur Verfügung, kann die
Speisung mit einem der Geräte

BS 48 i .................................. Best.-Nr. 06494
(für ein Mikrophon)

BS 48 i-2 ............................... Best.-Nr. 06496
(für zwei Mikrophone)

erfolgen. Beide Geräte liefern 48 V ± 1 V, maximal
je  5 mA,  und  werden  jeweils  von  einer  9 Volt-
Blockbatterie Typ IEC 6 F 22 gespeist.

Das Gerät BS 48 i-2 ist mit 5-poligen, das BS 48 i
mit 3-poligen XLR-Steckverbindern ausgerüstet.

(Siehe auch Neumann-Druckschrift 68832... „48 V-
Phantomspeisegeräte“).

Summary of Contents for KMR 81 i










Reviews: