background image

NTI VEEMUX VIDEO MATRIX SWITCH 

 

34

 

RS232 UPGRADE OF THE FRONT PANEL LCD FIRMWARE  

The firmware in the front panel LCD can be upgraded to include the latest features available using either the RS232 port 
(below) or Ethernet Control (page 24).   Follow the procedure below to use the RS232 method to update the Front Panel LCD 
firmware in the VEEMUX.     To prepare, first download the 

rmtlcd_va_1_x. hex

  file (x= the current firmware version) from 

the NTI Video Matrix Switch website 

http://www.networktechinc.com/vmtx.html

.  

The following will be needed

:  

o

 

1 PC running HyperTerminal (or other terminal program) equipped with a 9 pin or 25 pin serial port  

o

 

A VEEMUX made to use the Firmware Upgrade feature  

o

 

1 serial cable wired straight through to connect your PC's serial port to the 

RS232

 port on the VEEMUX (see 

cable  specifications on page 36) 

o

 

A firmware file for a VEEMUX downloaded from 

www.networktechinc.com

  

Procedure:  

1. 

Power OFF the VEEMUX.  

2. 

Connect the null modem cable between the serial port on the PC  and the 

RS232

 port on the VEEMUX. 

3. 

Use HyperTerminal to prepare to connect to the VEEMUX (using settings 9600 baud, 8-N-1 no flow). Make sure 
HyperTerminal has been configured for connection through the correct COM port on the PC. 

4. 

With the HyperTerminal window open, hold the spacebar and apply power to the VEEMUX. A command menu and the 
Command prompt (

>

) should appear. 

 

 

Copyright 2006 Network Technologies Inc 
 
Flash Loader Utility v1.0 
 
 
   H   Display this help menu 
 
   C   Clear flash 
 
   L   Load flash with .hex file 
 
 
 
Command> 
 

Note: Commands are not case-sensitive (for example, 'h' or 'H' will execute the help command), and the <Enter> key 
is not required to execute a command.    

 

 

If the Flash Loader Utility menu does not appear, the VEEMUX you have may have been made prior to the release of 
this product change.   To verify this, with the VEEMUX powered ON, at the HyperTerminal window enter the following 
command: 

RV 01

  

(be sure to include the space)

 

The following revision string will appear: 

$date: 2006/04/17 20:20:59 $$revision: 1.1 $$IN: 08 $$OUT: 04 $ 

If the date shown is

 before 

2006/04/17,   then the VEEMUX firmware cannot be upgraded using this procedure.  

 

 

Summary of Contents for VEEMUX SM-nXm-15V-LCD












































Reviews: