background image

 

 

4.

 

Set up Instruction

 

On/Off 

Power on 

Insert batteries. (Users may need a screwdriver to open) 

Turn on   

The magnet approach to the top cover for 3 seconds.   

Note:   

The device is in the geomagnetic initialization state within 3 minutes after turning on. Please do 

not move the device or cause changes in the surrounding magnetic field. 

Turn off 

(Restore to factory setting) 

The magnet approach to the top cover for 10 seconds 

Power off 

Remove Batteries.   

Note: 

1.

 

The device will be off after removing the battery and insert it again. 

2.

 

It is suggested to wait for at least 10 seconds between turning the device on and off. 

3.

 

To enter the engineering test mode: At 1

st

 to 5

th

 second after power on   

Network Joining

 

 

Never joined the network 

Turn on the device, and it will search for the network to join. 

Had joined the network 

(not at factory setting) 

Turn on the device, and it will search for the previous network to join. 

Reed Switch Function 

 

The magnet close to the top cover 

for 10 seconds 

Restore to factory setting / Turn off 

The magnet close to the top cover 

shortly 

The device is in the network: sends a report 

Sleeping Mode 

The device is on and in the network 

Sleeping period: Min Interval. 

When the reportchange exceeds setting value: send a data report according to Min Interval. 

Note: 

Suggest to remove batteries if the device is not used.   

     Suggest to check device verification on gateway. 

Low Battery Threshold 

Low Voltage 

3.2 V 

 

* Could use the magnet of R311A as the magnet mentioned in the article. For specific operation, please refer to the installation 

instruction picture below.   

Summary of Contents for R719A















Reviews: