NETGEAR PS121v2 - USB Mini Print Server User Manual Download | Manualshive

Page: 40 / 50

background image

NETGEAR USB Multifunction Printer Server PS121v2 User Manual

3-8

Operation

v1.1, September 2006

4.

To edit the IP settings, click

LAN IP Setup

in the main menu.

5.

Edit the IP address, IP subnet mask, and gateway IP address, as desired, and click

Apply

.

6.

To change the print server name, click

Configure Server

in the main menu, edit the name in

the Print Server Name text box, and click

Apply

.

Figure 3-9

Warning:

Normally, the DHCP Client field setting should be left in the

Disable

setting so that the IP address of the device remains fixed. It is not
recommended that you select

Enable

. If you do, the print server will find

an IP address for you automatically from the router or other DHCP server
in your network. When the DHCP server changes the IP address, you will
be disconnected from the Web GUI and unable to open it again unless
you can ascertain the reassigned IP address. Also, the SmartWizard
operates under the assumption that the IP address of the print server is
fixed.

Note:

The print server name must not contain any spaces.

«
...
38
39
40
41
42
...
»

Summary of Contents for PS121v2 - USB Mini Print Server



















































Reviews:

No comments

Related manuals for PS121v2 - USB Mini Print Server

Brand: Oki Pages: 2

Brand: Oki Pages: 52

Brand: Oki Pages: 117

Brand: Oki Pages: 45

Brand: Oki Pages: 112

Brand: Oki Pages: 115

Brand: Oki Pages: 2

Brand: Olympus Pages: 71

imagePRESS Server G200

Brand: Canon Pages: 82

Brand: Canon Pages: 88

Brand: IBM Pages: 198

Brand: Canon Pages: 21

Brand: Compuprint Pages: 38

ProLiant DL180 Gen10

Brand: HPE Pages: 10

Brand: Xerox Pages: 205

BladeCenter HS21 1885

Brand: IBM Pages: 140

Multi-Font NX-2415

Brand: Star Micronics Pages: 134

Fast T-Jet Blazer Pro

Brand: Screen Print & Inkjet Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands