NETGEAR Nighthawk X4S User Manual Download Page 157

Page: 157 / 185

Enter the router user name and password.

The user name is admin. The default password is password. The user name and password are case-sensitive.

The BASIC Home page displays.

Select ADVANCED > Advanced Setup > Port Forwarding/Port Triggering.

The Port Forwarding/Port Triggering page displays.

Select the Port Triggering radio button.

Click the Add Service button.

In the Service Name field, type a descriptive service name.

From the Service User menu, select a user option:

•

Any (the default) allows any computer on the Internet to use this service.

•

Single address restricts the service to a particular computer.

From the Service Type menu, select TCP or UDP or TCP/UDP (both).

If you are not sure, select TCP/UDP.

Customize Internet Traffic Rules for Ports

157

Nighthawk X4S AC2600 Smart WiFi Router

Summary of Contents for Nighthawk X4S


























































































































































































Search results

Summary of Contents for Nighthawk X4S

Reviews:

Related manuals for Nighthawk X4S

Brands by name

Popular brands

NETGEAR Nighthawk X4S, User Manual

Search results

Summary of Contents for Nighthawk X4S

Reviews:

Related manuals for Nighthawk X4S

Brands by name

Popular brands