NETGEAR Nighthawk X4S User Manual Download Page 128

Page: 128 / 185

To change your settings:

Launch a web browser from a computer or WiFi device that is connected to the network.

Enter http://www.routerlogin.net.

A login window opens.

Enter the router user name and password.

The user name is admin. The default password is password. The user name and password are case-sensitive.

The BASIC Home page displays.

Select ADVANCED > Advanced Setup > Dynamic DNS.

The Dynamic DNS page displays.

Change your DDNS account settings as necessary.

Click the Apply button.

Your settings are saved.

Use Dynamic DNS to Access USB Storage Devices Through the Internet

128

Nighthawk X4S AC2600 Smart WiFi Router

Summary of Contents for Nighthawk X4S


























































































































































































Search results

Summary of Contents for Nighthawk X4S

Reviews:

Related manuals for Nighthawk X4S

Brands by name

Popular brands

NETGEAR Nighthawk X4S, User Manual

Search results

Summary of Contents for Nighthawk X4S

Reviews:

Related manuals for Nighthawk X4S

Brands by name

Popular brands