manualshive.com logo in svg

NETGEAR JNR1010v2, User Manual

Share
Download
NETGEAR JNR1010v2 User Manual Download Page 21

Get Started with NETGEAR genie 

21

 JNR1010v2 N150 Wireless Router

The following screen displays:

3. 

Type the old password and type the new password twice.

4. 

If you want to be able to recover the password, select the 

Enable Password Recovery 

check box. 

Note:

NETGEAR recommends that you enable password recovery.

For more information, see 

Password Recovery 

on page

 

21.

5. 

Click the 

Apply

 button.

Password Recovery

NETGEAR recommends that you enable password recovery if you change the password for 
the router’s user name of admin. Then you have an easy way to recover the password when 
it is forgotten. This recovery process is supported in Internet Explorer, Firefox, and Chrome 
browsers, but not in the Safari browser.

To set up password recovery:

1. 

Log in to the router.

For more information, see 

Log In to Your Router After Installation 

on page

 

18.

2. 

Select 

ADVANCED > Administration > Set Password

. 

The Set Password screen displays.

3. 

Select the 

Enable Password Recovery

 check box.

Summary of Contents for JNR1010v2




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands