NETGEAR FSM726E - ProSafe Switch Hardware Installation Manual Download Page 3

v1.0, November 2008

3

This device must accept any interference received, including interference that may cause undesired operation. 

Note:

 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and 

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures: 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that which the receiver is connected. 

Consult the dealer or an experienced radio/TV technician for help. 

Canadian Department of Communications Radio Interference Regulations 

This digital apparatus (NETGEAR ProSafe 24-Port Ethernet L2 Managed Switch Model FSM726E) does not exceed the 
Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the 
Canadian Department of Communications. 

Règlement sur le brouillage radioélectrique du ministère des Communications

Cet appareil numérique (NETGEAR ProSafe 24-Port Ethernet L2 Managed Switch Model FSM726E) respecte les 
limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le 
brouillage radioélectrique du ministère des Communications du Canada. 

EN 55 022 Declaration of Conformance

This is to certify that the NETGEAR ProSafe 24-Port Ethernet L2 Managed Switch Model FSM726E is shielded against 
the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. 
Conformity is declared by the application of EN 55024 Class A (CISPR 22).

EN 55 022 and EN 55 024 Statements

This is to certify that the NETGEAR ProSafe 24-Port Ethernet L2 Managed Switch Model FSM726E is shielded against 
the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. 
Conformity is declared by the application of EN 55024 Class A (CISPR 22).

Warning: 

This is a Class A product. In a domestic environment, this product may cause 

radio interference, in which case the user may be required to take appropriate 
measures.

Customer Support

Refer to the Support Information Card that shipped with your ProSafe 24-Port Ethernet L2 
Managed Switch Model FSM726E.

Summary of Contents for FSM726E - ProSafe Switch































Reviews: