background image

Figures 1 and 2 show where one could place the ANT24O5 for best coverage in an office. In
Figure 1, the ANT24O5 is placed on the ceiling in the middle of the area to cover. In Figure 2,
the ANT24O5 is placed in an elevated location on an interior wall, above and facing the
indoor coverage. Notice that the area close to the antenna, behind or beside it, will still be
covered because the dynamic range of the WLAN transmitter/receiver and antenna is
approximately 100dB. So, even with 20dB to 40dB of attenuation, the signal strength is still
strong and communication is maintained. 

Placement and Other Important Considerations 

In order to maximize coverage, antennas must be placed in a good spot. A lot of improvement
can be achieved by optimizing the line of sight between antennas. Try to minimize the
partitions and partial obstructions if possible. For instance, place the antenna on a wall above
the cubicles (cubicles generally include a metal foil). Ideal placement is against a wall, 2m high,
or on the ceiling facing the area to cover.

The longer the antenna cable, the higher the attenuation, or signal loss. This will decrease the
range and performance. The best performance is achieved with a short cable between the
antenna and the wireless device. The shortest FCC approved antenna cable is the NETGEAR
1.5 M (ACC-10314-01) cable. For optimal performance, use a low-loss NETGEAR antenna
cable up to 10 meters long. 

If the wireless access point, router or gateway is in a IT room, place the antenna outside of the
room close to the ceiling against a wall. Use a NETGEAR antenna cable of up to 10 meters in
length to connect the antenna to the wireless access point. 

3

2

Approximate 
coverage area

Cubicles 

1.5m high

ANT24O5

Figure 2:

Optimal antenna placement on an interior wall

Approximate 
coverage area

Cubicles 

1.5m high

ANT24O5

Figure 1:

Optimal antenna placement on the ceiling

NETGEAR ANT24O5 Install.qxd  7/2/03  7:11 AM  Page 4

Summary of Contents for ANT24O5








Reviews: