background image

201-10080-01

iii

Federal Communications Commission (FCC) and European Radiation 

Exposure Statements

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In 
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the 
antenna shall not be less than 30 cm (12 inches) during normal operation. This device should not be 
co-located with other transmitters.

European Emission Statement

For EU, use of any antenna requires careful planning and extra consideration to comply with EU emissions, 
health standards and regulations. It is recommended that a qualified professional installer service is 
consulted for site survey and proper installation. Antenna installation must comply with the maximum level 
authorized by each country. See http://www.NETGEAR.com/go/antannas_eu for product combinations that 
comply with EU regulations.

Safety

The NETGEAR wireless devices WG302, FWG114P, FVM318, ME103, and FM114P have been tested with the antenna 
ANT2409 and have successfully passed all relevant tests contained in the Standard for the Safety of Information 
Technology Equipment for Europe (EN 60950-2000) equivalent to North American Standards UL 60950, Third Edition, 
CAN/CSA-C22.2 No. 60950-00, Third Edition and Australian/New Zealand Standards ACA TS 001-1997, and AS/NZS 
3260:1993 with A1 through A4.

Summary of Contents for 2409



























Reviews: