background image

Net Safety Monitoring Inc

I

MPORTANT

 I

NFORMATION

This manual is for informational purposes only. Although every effort has been 
made to ensure the correctness of the information, technical inaccuracies may 
occur and periodic changes may be made without notice. Net Safety Monitoring 
Inc., assumes no responsibility for any errors contained within this manual.

If the products or procedures are used for purposes other than as described in the 
manual, without receiving prior confirmation of validity or suitability, Net 
Safety Monitoring Inc., does not guarantee the results and assumes no 
obligation or liability.

No part of this manual may be copied, disseminated or distributed without the 
express written consent of Net Safety Monitoring Inc.

Net Safety Monitoring Inc., products are carefully designed and manufactured from 
high quality components and can be expected to provide many years of trouble free 
service. Each product is thoroughly tested, inspected and calibrated prior to 
shipment. Failures can occur which are beyond the control of the manufacturer. 
Failures can be minimized by adhering to the operating and maintenance 
instructions herein. Where the absolute greatest of reliability is required, 
redundancy should be designed into the system.

Warranty

Net Safety Monitoring Inc., warrants its ST1400 sensor against defective parts 
and workmanship for a period of 6 months from date of purchase; other 
electronic assemblies for 36 months from date of purchase.

No other warranties or liability, expressed or implied, will be honoured by Net 
Safety Monitoring Inc.

Contact Net Safety Monitoring Inc., or an authorized representative for details.

We welcome your input at Net Safety Monitoring. If you have any comments 
please contact us at the phone/address below or visit our web site and complete 
our on-line customer survey: www.net-safety.com.

Contact Information

Net Safety Monitoring Inc.
2721 Hopewell Place NE
Calgary, AB  T1Y 7J7
Canada
Telephone: (403) 219-0688 Fax: (403) 219-0694
www.net-safety.com
E-mail: [email protected]

Copyright © 2005  Net Safety Monitoring Inc. 
Printed in Canada

Summary of Contents for Millennium MLP-A-ST1400-25





























Reviews: