Ness S2 Installation And User Manual Download Page 10

Page: 10 / 10

Specifications

Features

Description

Appearance

Metal case, anti-explosion and anti-tamper

Waterproof

IP65

Input voltage

DC: 12-24V AC: 12-18V

Users(max)

2500

4 digits

Master Card

Add/Delete User

Proximity Reader (RFID)

Supports Wiegand 26bits, PIN/Wiegand output is a virtual number, Site
Code / Reader Address is set within the S2 Controller

Connect External reader

Can Connect any External EM/HID/IC readers with Wiegand 26 bit Output

Connect High Power Alarm

External Current of the Alarm <=3A

Dimensions

135mm x 57mm x 25mm

Operating Voltage

DC:12~24V AC: 12~18V

Current

Idle – 35mA / Active <80mA

Card Reading Distance

3~6 cm

Operating Temperature

-40~60 Deg C

Lock Output Load

2A Max

Head Office:

4/167 Prospect Hwy,

Seven Hills NSW, Australia

Phone +61 2 8825 9222

email : [email protected]

Sydney Office - (02) 8825 9222

Melbourne Office -(03) 9875 6400

Brisbane Office - (07) 3399 4910

Perth Office -(08) 9328 2511

Adelaide Office - (08) 8152 0000

Email

[email protected]

Summary of Contents for S2











Search results

Summary of Contents for S2

Reviews:

Related manuals for S2

Brands by name

Popular brands

Ness S2, Installation And User Manual

Search results

Summary of Contents for S2

Reviews:

Related manuals for S2

Brands by name

Popular brands