Ness 106-304 Installation Notes Download Page 10

Page: 10 / 12

Relay menu steP-By-steP

Program the RELAY TYPE and RELAY OUTPUT CONTROL

PRogRammIng

STEP DESCRIPTION

ACTION

DISPLAY NOTE

To enter program mode place
the link on the Program pins.

Program

Press SELECT to display

PRESS

RELAY MENU

Program the Relay tyPe

When

is displayed, press

and hold SELECT.

LONG PRESS

RELAY TYPE MENU

When

is displayed, press

and hold SELECT.

LONG PRESS

The currently programmed
option in the RELAY TYPE
MENU is displayed

Repeatedly pressing SELECT will cycle through the
available options in the RELAY TYPE MENU, being

Exit

Latch

Toggle

Pulse

Choose the required option
then press and hold SELECT
to save.

LONG PRESS

The saved option will flash
twice then the display
returns to the RELAY MENU

Program the Relay outPut ContRol

When

is displayed, press

and hold SELECT.

LONG PRESS

The first item in the RELAY
MENU is displayed, being
RELAY TYPE

Press SELECT until

displayed.

PRESS

RELAY OUTPUT CONTROL
MENU

When

is displayed press

and hold SELECT

LONG PRESS

The currently programmed
option in the RELAY
OUTPUT CONTROL MENU

is displayed

Repeatedly pressing SELECT will cycle through the
available options in the RELAY OUTPUT CONTROL
MENU, being

On/Alarm

Low

battery

AUX

Panic/

Tamper

Exit

Choose the required option
then press and hold SELECT
to save.

LONG PRESS

The saved option will flash
twice then the display
returns to the RELAY MENU

Summary of Contents for 106-304













Search results

Summary of Contents for 106-304

Reviews:

Brands by name

Popular brands

Ness 106-304, Installation Notes

Search results

Summary of Contents for 106-304

Reviews:

Brands by name

Popular brands