Ness 101-076 Quick Manual Download Page 5

 

 

Set a new Program code 

 
 

 
Enter Program Mode 
 
Press 3 - (the transmit LED will turn red) 
 
Enter your new 4-Digit programming code 
 
Once your programming code has been entered then it will exit programming 
mode automatically. - (Transmit LED will turn red) 
 

 

Changing the facility code 

 

Note:

 

Facility code can 
range between 
000 - 255

 

 
Factory Default:

 


 

 
Enter Program Mode 
 
Press 4 - (the transmit LED will turn red) 
 
Enter the new 3 digit code you wish to set as the facility code. 
 
Once you have entered the new facility code then it will exit programming mode 
automatically. - (Transmit LED will turn red) 
 

 

Factory Default Settings 

 
 

 

Warning:

 

This will erase the entire memory, settings and codes to factory default.

 

 
Enter Program Mode 
 
Press 0 - (the transmit LED and Program LED will flash red) 
 
Enter Program code to confirm (default: 1234) 
 
Entering the wrong program code will exit programming mode and will return to 
normal mode and will not erase any memory. 
 

 

Replace a lost programming code 

 
 

 
Remove power from the unit 
 
Activate the tamper by removing the reader from the wall or removing the readers 
case. 
 
Apply power to the reader. 
 
You now have 10 seconds to enter programming mode by using the factory 
default programming code of 1234. 
 

 

Summary of Contents for 101-076











Reviews: