Neptune Apex WAV Quick Start Manual Download Page 16

 

WAV QuickStart Guide 

Page 14 

of Neptune Systems’ products. Buyer’s remedies for breach of warranty shall be limited to repair, or 

replacement and full or partial adjustment to purchase price. 
 
Information in this manual is subject to change without notice. Please see www.neptunesys.com for the latest 
product information and product updates. 
 

15750 Vineyard Blvd, Suite 150 

Morgan Hill, CA  95037 

http://www.neptunesystems.com 

[email protected] 

Phone 408-779-4090    Fax 408-762-2042 

  

©

2016 

Neptune Systems - All Rights Reserved 

 
 

CE DECLARATION OF CONFORMITY 

Manufacturer: Neptune Systems, 15750 Vineyard Blvd, Suite 150, Morgan Hill, CA  95037; 408-779-4090 
Product: WAV  

Model No.  WAV200-002 

 
The undersigned hereby declares, on behalf of the Neptune Systems, LLC. of Morgan Hill, California that the above-
referenced product, to which this declaration relates, is in conformity with the provisions of: 

 

EN 60950-1+A1:2009  

 

EN 60335-1:2010 

 

The Technical Construction File required by this Directive is maintained at the corporate headquarters of Neptune Systems, 
15750 Vineyard Blvd, Suite 150, Morgan Hill, California. 

 

  
________________________ 

Curt Pansegrau 
President 

  

                                                 

 

 
 

The symbol to the right means that according to local 
laws and regulations your product should be disposed 
of separately from household waste. When this 
product reaches its end of life, take it to a collection 
point designated by local authorities. Some collection 
points accept products for free. The separate 
collection and recycling of your product at the time of 
disposal will help conserve natural resources and 
ensure that it is recycled in a manner that protects 
human health and the environment. 

 

 

Summary of Contents for Apex WAV

















Reviews: