Neptune 7000 Series Installation Operation & Maintenance Download Page 8 | Manualshive

Page: 8 / 25

background image

7

SECTION I

PARTS ORDERING INSTRUCTIONS

The complete model number and serial number of the pump must be furnished to insure

prompt and accurate parts service. These numbers are found on the name plate (sample

below) located on the back cover of the pump.

Please refer to page number (17), (18), (19), (20) for parts list. Ballooned drawing of the

pumps can be found on pages (13), (14), (15), (16) and (20).

Spare Parts Kits are found on pages 22 and 23.

Send all orders or inquiries for parts to:

Parts Department

Neptune Chemical Pump Company, Inc.

295 DeKalb Pike

North Wales, PA 19454

Tel.: 215-699-8700

1 -888-3NEPTUNE (888-363-7886)

FAX: 215-699-0370

Web: www.Neptune1.com

Email: [email protected]

NOTE:

PLEASE SUPPLY BOTH MODEL AND SERIAL NUMBERS.

«
...
6
7
8
9
10
...
»

Summary of Contents for 7000 Series


























Reviews:

No comments

Related manuals for 7000 Series

Brand: TapFlo Pages: 13

Brand: Walchem Pages: 34

Brand: WAGNER Pages: 84

Brand: WAGNER Pages: 52

MiniTank WM-2.5

Brand: Waiwela Pages: 20

Brand: TESY Pages: 176

Brand: Idex Pages: 40

FastHeat Digital 14160

Brand: Kerbl Pages: 32

Brand: SKF Pages: 12

Brand: baracuda Pages: 14

Brand: deconta Pages: 12

Brand: Pfeiffer Vacuum Pages: 52

Brand: blupura Pages: 28

Wilo-Sub TWU 3 HS Series

Brand: Wilo Pages: 192

Brand: Fass Pages: 13

Brand: Bradford White Pages: 2

Brand: NEXT pool Pages: 19

Brand: WarmPool Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands