manualshive.com logo in svg

Neousys Technology PB- 2500J-CSM, User Manual, Page: 35 / 44

Share
Download
Neousys Technology PB- 2500J-CSM User Manual Download Page 35

  PB-2500J-PCIe/ CSM

 

35 

4.2.1 

Auto-start 

 

Auto-start Settings 

Auto-start _ 

seconds after 

DC applied 

If the 

“

Auto-start

”

 box is checked, the system will start __ 

seconds after the 3-pin pluggable terminal block is plugged 

into the system (DC applied).

 

If the 

“

Auto-start

”

 box is not checked, once you have plugged 

in the 3-pin pluggable terminal block, you will need to press the 

power button to turn the system on.

 

Buzzer on 

If the 

“

Buzzer on

”

 box is checked, a buzzer sound will sound 

as soon as the supercapacitors start to discharge (supplying 

power to the system).

 

If the 

“

Buzzer on

”

 box is not checked, no buzzer sound will be 

made when the supercapacitors start to discharge.   

 

 

NOTE 

For new parameters to take effect, you must click on 

“

Update Parameters

”

 and 

follow procedure instructions. Please refer to the relevant section for details. 

Summary of Contents for PB- 2500J-CSM













































Reviews:

No comments