background image

 

 

 
 
 
 
User Manual 
 
Digital Hotplate Magnetic Stirrer 
Item N°. D-6010  

 

 

 

 

 

 

 

 

 

 
 
Users should read this Manual carefully, follow the instructions and procedures, and be aware of the 
dangers while using this instrument. 

 
Safety Instructions 

Warning! 

 

 

Read the operating instructions carefully before use the instrument 

 

Ensure that only trained staff work with the instrument 

 

Forbid to heat the substances with low burning point or easy-volatile( hotplate ) 

                Risk of bum! 

 

Caution when touching the housing parts and the heating plate. 

        The heating plate can reach temperatures of 340°C! 

 

Pay attention to the residual heat after switching off. 

 

Protective ground contact! 

 

 

Make sure that socket must be earthed (protective ground contact) before use 

 

When work, wear suitable protective clothing to avoid the risk from: 

 

Splashing and evaporation of liquids 

 

Release of toxic or combustible gases. 

 

Set up the instrument in a spacious area on a solid, clean, non-slip, dry and fireproof surface, do not 
operate the instrument in explosive atmospheres with hazardous substances or under water. 

 

Gradually increase the speed, reduce the speed if : 

 

The stirring bar breakaway because of too high speed 

 

The instrument is not running smoothly, or container moves on the base plate. 

 

Temperature must always be set to at least 25°C lower than the fire point of the media used. 

 

Beware of hazards due to

 

 

Flammable materials or media with a low boiling temperature 

 

Overfilling of media 

 

Unsafe container 

 

Process pathogenic materials only in closed vessels. 

 

If the case of the stirrer bar is PTFE, please note: 

Elemental fluorine, three fluoride and alkali metals will corrode the PTFE and Halogen Alkanes make it expansion 
at room temperature. Molten alkali, alkaline earth metals or their solution, as well as the powder in second and 
third ethnic of the periodic table of Elements will have chemical reaction with PTFE when temperature reaches 
300 – 400°C. 
 
 
                            neoLab Migge Laborbedarf-Vertriebs GmbH, Rischerstr. 7-9, 69123 Heidelberg  
                                         Tel. 06221 / 84 42-0      [email protected]      www.neolab.de      
 
 
 
         neoLab Berlin Tel. 030 / 30 87 45-0                                     neoLab München Tel. 089 / 35 61 88 -0 
 

Summary of Contents for D-6010






Reviews: