background image

9

11. Warranty

 

One Year Limited Warranty

The  quality  controls  used  in  the  manufacture  of  this  product  will  ensure  your 

satisfaction. This warranty applies only to the original purchaser of this product 

from an authorized  dealer. This warranty covers any supplied or manufactured 

parts of this product that, upon inspection by  authorized personnel, is found to 

have failed in normal use due to defects in material or workmanship. This warranty 

does not apply to installation expenses. Attempting to service or modify this unit, 

operating this unit under conditions other than the recommended voltage  will render this  

WARRANTY VOID.

Unless otherwise prescribed by law,  shall not be liable for any personal injury, 

property  damage  and  or  any  incidental  or  consequential  damages  of  any  kind 

(including water damage) resulting from malfunctions, defects, misuse, improper 

installation or alteration of this product. All parts of this  product are guaranteed 

for a period of 1 year as follows:

Within the first 12 months from date of purchase, subject to the conditions above,  

will repair or replace the product at their discretion, if it is defective in material or 

workmanship providing it is returned to an Authorized  Neo Car Audio Dealer, with 

PROOF OF PURCHASE from an authorized  dealer.

Warning

:

This equipment may be reset by unintentional electrostatic discharge during op-

eration. Exposure to direct sunlight or extreme heat may cause damage or mal-

function.

FCC Class B Radio Frequency 
Interference Statement

 

This equipment has been tested and found to comply with the limits for a Class 

B digital device, pursuant to Part 15 of FCC rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential instal-

lation. This equipment generates, uses, and can radiate radio frequency energy 

and,  if  not  installed  and  used  in  accordance  with  the  instructions,  may  cause 

harmful  interference  to  radio  communications.  However, there  is  no  guarantee 

that interference will not occur in a particular installation. If this equipment does 

cause  harmful  interference  to  radio  or  television  recption,  which  can  be  deter-

mined by turning the equipment off and on, the user is encouraged to try to correct 

the interference by one or more of the following measures:

        1. Reorientate or relocate the receiving antenna.

        2. Increase the separation between the equipment and receiver.

        3. Connect the equipment into an outlet on a circuit different from

            that of which the receiver is connected. 

        4. Consult the dealer or an experienced radio / television technical for help.

Notice : The changes or modifications not expressly approved by the party re

-

sponsible for compliance could void the user authority to operate the equipment.

Summary of Contents for TY1















Reviews: