Nemesis CCS-2 User Manual Download Page 22 | Manualshive

Page: 22 / 22

Nemesis CCS-2 User Manual Download Page 22

Nemesis Audio

22

Technical Specifications

Mains Input Voltage:  .......................................... Powercon, 100-240VAC 50/60Hz, Internally Protected
Rated Power .................................................................................................................................... 50.4W
GPI XLR Input Protection: .............................................. Closed Contact to Ground, Protected to +/- 70V
GPI XLR Maximum Cable Length ....................................................................................................... 100m
5-Pin Remote Relay Contact Rating  .......................................................... Closed Contact to Ground, 1A
GPO Output Power Rating:  ................................ 12V @ 500mA, 5V @ 500mA, Over-Current Protected
GPO Relay Contact Rating:  ........................................................................................ 1A, 125VAC, 60VDC
Video Connection ........................................................................ DVI-I Connector, Single-Link DVI + VGA
CPU USB Link .................................................... USB B, Class-Compliant USB MIDI, 12Mbps Internal Hub
Programming USB Link ............................................................................. Mini USB, HID Class-Compliant
Equipment Dimensions (HxWxD) ..................................................................................... 44x482x272mm
Weight ............................................................................................................................................... 3.7Kg

Internal Jumpers

Label

On

JP2, JP3

Enable/disable additional out (pins 1+3) on MIDI A

JP4, JP5

Enable/disable additional out (pins 1+3) on MIDI B

JP1

Enable battery backup for on board clock

Notes:

*This manual is based on CCS-2 Firmware v1.3.1

Document Revision 1.0 04/09/17 RC

- END OF DOCUMENT -

«
...
20
21
22

Summary of Contents for CCS-2























Reviews:

No comments