background image

 

Page | 8 

 

P: 419.542.7751    F: 419.5426690   800.782.761   nemcofoodequip.com 

 

 

 

If you want to set seconds, for instance 3 minutes and 30 seconds, press the ‘ʌ’ 
button until the display shows ‘03.59’ minutes.  Then press the ‘MIN/SEC’ button 
again.  The ‘seconds’ field will flash.  Press the ‘v’ button to adjust the seconds to 
30.  The display will show ‘03.30’ 

 

When the time is set to what you want, press the ‘Start/Stop’ button.  The power 
will come on and the timer will count down.  When the timer counts down to 0, 
the unit will stop heating. 

 

While the unit is heating, the display will alternate between the timer and the 
power setting.  You can always adjust the power setting using the ‘ʌ’ and ‘v’ 
buttons while the display is showing the power level. 

 

If you press the TMR button while the unit is heating, the display will stop 
alternating between the timer and the power level.  The timer will continue to 
run.  Pressing the TMR button again will resume alternating the display. 

 

While the unit is heating, the timer display decimal points will flash. 

 

Once the timer counts down to zero, pressing the ‘Start/Stop’ button will restart 
the cycle at the time that you set previously.  Turning the unit off/on using the 
‘Power’ Button will reset the timer to 719 minutes. 

 

Cleaning the Induction Range   

After the induction range has cooled down, clean as follows: 

Glass Cooktop:  Wipe with a damp cloth or use a mild, non-abrasive cleaning solution. 

Stainless Steel Body:  Clean with a damp soft cloth or a mild cleaning solution or stainless                
cleaner/polish. 

Control Panel:  Wipe with a damp cloth only.  Do not spray with cleaning solutions!  Do not use 
sharp or metal objects to press the buttons!   Only press the buttons using your finger!! 

Air Filter:  Remove the air filter located underneath the unit by pulling it out from the front. 

                   Wash/rinse by hand using warm water and detergent to remove oil/grease and dust. 

                   Dry thoroughly and re-install the filter on the guides underneath the unit.   

 

 

DO NOT USE SHARP OBJECTS OR ABRASIVES ON THE GLASS COOKTOP.  SCRATCHES IN THE GLASS CAN 
WEAKEN IT AND LEAD TO BREAKAGE! 

Summary of Contents for 9130













Reviews: