background image

APPLICATION

AR luminaires are designed for use indoors, outdoors, wet locations, and areas containing moisture, 

dirt, corrosion, vibration, and rough usage. NSF Models (ARxx-xxx-xx-xx-FS-XX) of the luminaire is 

certified by NSF for use in Splash-zone and Non-Food areas of food processing locations as defined in 

NSF-2. The AR luminaire is also certified for use on marine vessels inside, outside and in other severely 

wet saltwater environments. Models ARXX-XXX-XX-XX-HZ-XX are certified for use in hazardous location 

areas.

UL File Numbers:                    Nemalux General Location: E477827

 

 

 

        Nemalux Hazardous Location: E477829

AR luminaires are suitable for use in the following areas as defined by the National Electrical Code 

(NEC) and the Canadian Electrical Code (CEC):

Certifications all models:      UL 1598, UL 1598A and UL 8750; 

 

 

 

        CSA C22.2 No. 250.0 and CSA C22.2 No. 250.13 

 

 

 

        ABS Listed

Certifications Hazardous Location models (ARXX-XXX-XX-XX-HZ-XX)

 

 

 

        UL 844, CSA C22.2 No. 137

 

 

 

        Hazardous Location Approved Locations: 

 

 

 

        Class I, Division 2, Groups ABCD, T4; 

 

 

 

        Class II, Division 2, Groups FG, T4A; 

 

 

 

        Class III;

 

 

 

        Class I, Zone 2, Group IIC;

 

 

 

        Zone 22

Certifications NSF models (ARXX-XXX-XX-XX-FS-XX)

 

 

 

        NSF/ANSI 2 Splash and Non-Food Zone

Housing:  

 

          Copper-free Cast Aluminum with Polycarbonate lens

Input Voltage:   

          Based on luminaire suffix in table below: Suffix - AC: 120-277 VAC | Suffix - HV: 347-480 

VAC  

 

Inrush Current:                    AR (AC): Inrush Current Peak / >50% Duration 120V: 62A / 210uS  277V: 148A / 200uS

                                                  AR (HV): Inrush Current 347V: 118.4A / 97uS Peak / >50% Duration 480V: 148A / 79uS

Connections:   

          2 x 3/4” NPT Conduit | Black: Line | White: Neutral/Line 2 | Green: Ground

 

 

 

          

Optional:   Violet (Purple): 0-10V Dimming (+)  |  Grey: 0-10V Dimming (-)

  

 

 

          For connections use wire rated to a minimum of 90°C.  Class 1 Wiring only.

 

 

 

          Dimming control wires must be rated 300V minimum for luminaires with suffix AC, 

 

 

 

          600V minimum for luminaires with suffix HV.

Ingress Protection: 

           IP66/67  | Suitable For Wet Locations. Marine Outside Type (Salt Water)

TM

Nemalux

I N D U S T R I A L

AR Series

rev. A-30

1-16

www.nemalux.com  |   [email protected]  |   Tel 403•242•7475  |   Fax 403•243•6190 

MADE IN CANADA

Installation

Spec Sheet

Webpage

The AR Series Installation Manual

*White fixture only

Summary of Contents for AR Series

















Reviews: