background image

 
- Noise. A degree of noise from the machine is not avoidable. Route noisy work is to 

be  licensed  and  limits  for  certain  periods.  Keep  rest  periods  and  they  may  need  to 

restrict the working hours to a minimum. For their personal protection and protection 

of people working nearby, an appropriate hearing protection shall be worn; 

-  Vibration. Warning:  The  actual  existing  vibration  emission  value  during  use  of  the 

machine  can  deviate  from  the  manual  or  the  manufacturer  specified.  This  can  be 

caused by the following factors, before or during each of use should be considered: 

- If the machine is used correctly 

- If the method of cutting the material and how it is processed correctly. 

- The use of the machine state is in the regulatory 

- Sharpness condition of cutting tool or cutting tool real 

- The grab handles are mounted back to optional vibration handles and are they fixed 

to the machine body. 

If you notice an unpleasant sensation or skin discoloration during use of the machine 

on your hands once you stop working. Place an adequate work breaks. In disregard 

of adequate work breaks, there may be a hand-arm vibration syndrome. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for CT2298









































Reviews: