background image

 

9

CAUTION

VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR 

AN ATTACHMENT.BE AWARE OF CHANGING CONDITIONS ON SLOPS.

 

 

 OPERATION 

 

1.  Refer to the vehicle owners manual for instruction on safe operation on slops. 

2.  For best handling and traction, distribution the weight of the load evenly in the cart. 

3.  Always test to make sure your tractor has adequate towing and braking capabilities whenever 

hauling a substantial amount of weight in your cart. Use extra caution when operating on slopes. 

 

NOTE 

DO NOT EXCEED WEIGHT CAPACITY OF CART.(See the specification on the page.) 

 

4.  Do not unhook your cart from the tractor while on a slope. The cart could unexpectedly roll down the 

slope. 

5.  Backing up with a 4 wheel steerable cart takes practice! Before using the cart for hauling, practice 

braking the empty cart in a level ,open area. 

6.  To empty material from the cart, remove the tailgate by lifting it straight up and out from between the 

guides. Material can then be raked or pulled our from the rear of the cart. 

7.  The maximum towing speed for this cart is 10km.p.h. 

 

 

MAINTENANCE 

1.  At the beginning of each season, lubricate, with a light machine oil, all bolt that are pivot points, 

lubricate, with a light split plastic bearings for the front axle spindles. 

2.  Grease or oil the wheel bearings periodically. Use automotive wheel bearing type grease of 20 

weight oil. 

3.  Keep tires filled to the recommended tire pressure of 30PSI. 

 

 

 

SPECIFICATION FOR 18 CU.FT 4 WHEEL CART 

 

 

 

 

 

 

 
 
 
 
 
 

Tires:

 

16.0”x6.5” Pneumatic.Turf Tread

 

Axles:

 

3/4” Dia .Steel

 

Capacity:

 

Up to 1800lbs. (907kgs) Max.

 

Approx.Sh.Wt:

 

211lbs.

 

Summary of Contents for CT2217













Reviews: