NEFF I16RPS8S5, User Manual

Page: 7 / 24

Basic operation
en
7
7.5 Switching off intensive mode
▶
To select a fan setting of your choice, press ⁠.
7.6 Switching on the fan run-on
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
The fan run-on removes remaining odours and is used
to dry the odour filter after the cooking process.
▶
Press ⁠.
a
LED 1 for the fan setting lights up in the LED dis-
play. LED 6 flashes for the fan run-on.
a
The appliance switches off automatically after ap-
prox. 10 minutes.
7.7 Switching off the fan run-on
▶
Press ⁠.
a
This immediately stops the fan run-on.
a
The appliance switches to the fan setting that was
previously selected.
7.8 Switching on automatic mode 1
The optimum fan setting is set automatically using a
sensor.
▶
Press ⁠.
a
In the LED display, LED 6 lights up for automatic
mode.
7.9 Switch off automatic mode
1
▶
Press ⁠.
a
The appliance switches to the fan setting that was
previously set.
a
The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a
Automatic mode runs for a maximum of four hours.
7.10 Sensor sensitivity 1
In automatic mode, a sensor in the appliance detects
the intensity of the cooking odours and roasting
odours. Depending on the setting of the sensor sensit-
ivity, the optimum fan setting is automatically switched
on.
If the sensor control reacts too weakly or too strongly,
you can change the setting for the sensor sensitivity.
¡
Default setting: Fan setting 3
¡
Lowest setting: Fan setting 1
¡
Highest setting: Fan setting 5
7.11 Setting the sensor sensitivity 1
Requirement:
The appliance is switched off.
1. Press and hold ⁠ and ⁠ for approx. 3 seconds.
2. Press ⁠ or to change the setting.
To cancel the setting, press ⁠.
3. To save the setting, press and hold ⁠ and for ap-
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a
A signal tone sounds as soon as the selected set-
ting is saved.
7.12 Intermittent ventilation
In order to regularly ventilate your kitchen, you can use
the interval ventilation. With interval ventilation, the vent-
ilation system switches on and off in the selected set-
ting for the selected time.
Note: This function is only available in the Home Con-
nect app.
If the interval ventilation is switched on, LED 6 continu-
ously flashes in the LED display for the interval ventila-
tion and the LED for the selected fan setting lights up.
As soon as the ventilation time ends, the LED for the
fan setting you have selected goes out. LED 6 contin-
ues to flash.
7.13 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡
After the appliance has been switched off, LED 1
flashes in the LED display for the grease filter satura-
tion display and/or LED 2 flashes for the saturation
indicator for the odour filter.
¡
A signal sounds repeatedly.
▶
Press .
a
The saturation indicator is reset.
7.14 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement: The appliance is switched off.
1. Press and hold ⁠ and ⁠ for approx. three seconds.
‒
To set circulating-air mode (non-regenerable fil-
ter), press ⁠/ until LED 2 lights up in the LED
display.
‒
To set circulating-air mode (non-regenerable fil-
ter), press ⁠/ until LED 3 lights up in the LED
display.
‒
To convert the electronic control back to opera-
tion without the air recirculation filter, press ⁠/
until LED 1 lights up on the LED display.
2. To save the setting, press and hold ⁠ and ⁠ for ap-
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
To cancel the setting, press ⁠.
a
A signal tone sounds as soon as the selected set-
ting is saved.
7.15 Switching on the lighting
▶
Press to switch on the lighting.
Note: Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
1
Depending on the appliance specifications