background image

11

en

Prior to installation

 

Round pipes:

 

We recommend

 

Internal diameter: 

150 mm

 (at least 120 mm).

 

Flat ducts 

must have an internal crosssection 

that equates to that of round pipes.

 

There should be no sharp bends.

 

ø 120 mm approx. 113 cm

2

 

ø 150 mm approx. 177 cm

2

 

If pipes have different diameters:

 Insert seal-

ing strip.

 

For exhaust-air mode,

 ensure that there is an 

adequate supply of fresh air.

Connecting a Ø 150 mm exhaust-air pipe:

 

Mount the pipe directly onto the air outlet on the 

hood.

Connecting a Ø 120 mm exhaust-air pipe:

 

Attach the reducing con-

nector directly to the air 

pipe.

 

Attach the exhaust-air 

pipe to the reducing con-

nector.

Circulating-air mode

 

With activated carbon filter if exhaust-air mode 

is not possible.

 

The complete installation set can 

be obtained 

from specialist

 outlets. 

The corresponding accessory numbers 

can be found at the end of these oper-

ating instructions.

Electrical connection

WARNING: THIS APPLIANCE MUST BE 

EARTHED
IMPORTANT: Fitting a Different Plug:

The wires in the mains lead are coloured in accord-

ance with the following code:
 

Green and Yellow  – Earth

 

Blue  

 

– Neutral

 

Brown    

– Live

If you fit your own plug, the colours of these wires 

may not correspond with the identifying marks on 

the plug terminals.
This is what you have to do:

1.  Connect the green and yellow (Earth) wire to 

the terminal in the plug marked ‘E’ or with the 

symbol ( ), or coloured green or green and yel-

low.

2.  Connect the blue (Neutral) wire to the terminal 

in the plug marked ‘N’ or coloured black.

3.  Connect the brown (Live) wire to the terminal 

marked ‘L’, or coloured red.

The extractor hood 

should only be connected to an 

earthed socket that has been installed according to 

relevant regulations.
If possible, site the earthed socket directly behind 

the chimney panelling.

 

The earthed socket should be connected via its 

own circuit.

 

If the earthed socket is no longer accessible fol-

lowing installation of the extractor hood, ensure 

that there is a permanently installed disconnec-

tor.

If it is necessary to wire the extractor hood di-

rectly into the mains:

The extractor hood should only be connected to the 

electricity supply by a properly qualified electrician.

A separator must be installed in the household 

circuit. A suitable separator is a switch that has a 

contact gap of more than 3 mm and interrupts all 

poles. Such devices include circuit breakers and 

contactors.

 

If the connecting cable for this appliance 

is damaged, the cable must be replaced by the 

manufacturer or his customer service or a similarly 

qualified person in order to prevent serious injury to 

the user.

Preparing the wall

 

The wall must be flat and perpendicular.

 

Ensure that the wall is capable of providing a 

firm hold for mounting screws and plugs.

Weight in kg: 20.

We reserve the right to construction changes within 

the context of technical development.

Summary of Contents for D96W44N0GB

















Reviews: