background image

en

    Important safety information

16

:

Warning – Risk of electric shock! 

Components inside the appliance may have 

sharp edges. These may damage the 

connecting cable. Do not kink or pinch the 

connecting cable during installation.

Risk of electric shock! 

It must always be possible to disconnect 

the appliance from the electricity supply. 

The appliance must only be connected to a 

protective contact socket that has been 

correctly installed. 

The mains plug of the mains power cable 

must be easily accessible after installation 

of the appliance. If this is not possible, an 

all-pole isolating switch must be integrated 

into the permanent electrical installation 

according to the conditions of overvoltage 

category III and according to the installation 

regulations.

The permanent electrical installation must 

only be wired by a professional electrician. 

We recommend installing a residual-current 

circuit breaker (RCCB) in the appliance's 

power supply circuit.

:

Warning – Risk of electric shock! 

Incorrect repairs are dangerous. Repairs may 

only be carried out and damaged power 

cables replaced by one of our trained after-

sales technicians. If the appliance is defective, 

unplug the appliance from the mains or switch 

off the circuit breaker in the fuse box. Contact 

the after-sales service.

:

Warning – Danger of suffocation! 

Packaging material is dangerous to children. 

Never allow children to play with packaging 

material.

Summary of Contents for D96BMU5N0A





















Reviews: