background image

Customer service    

en

13

4

Customer service

Customer service

When calling us, please give the product number (E 

no.) and the production number (FD no.) so that we can 

provide you with the correct advice. The rating plate 

with these numbers can be found inside the appliance 

(remove the metal mesh grease filter to gain access).
You can make a note of the numbers of your appliance 

and the telephone number of the after-sales service in 

the space below to save time should it be required.

Please be aware that a visit by an after-sales engineer 

will be charged if a problem turns out to be the result of 

operator error, even during the warranty period.
Please find the contact data of all countries in the 

enclosed customer service list.

To book an engineer visit and product advice

Rely on the professionalism of the manufacturer. You 

can therefore be sure that the repair is carried out by 

trained service technicians who carry original spare 

parts for your appliances.

Accessories

(not included in the scope of delivery)

Note: 

These instructions apply to several appliance 

models. It may be the case that an optional accessory 

that is listed does not apply for your appliance.

Note: 

Observe the installation instructions in the 

accessory.

--------

--------

E no.

FD no.

After-sales service

O

GB

0344 892 8989 

Calls charged at local or mobile rate.

IE

01450 2655 

0.03 € per minute at peak. Off peak 0.0088 € 

per minute.

Accessory - narrow 260 mm

Order number

Starter set for air recirculation mode 
Easy-change filter for starter set

Z5101X5
Z5101X1

CleanAir recirculation module
Easy-change filter for CleanAir recirculation mod-

ule (cannot be regenerated)

Z5270X0
Z5170X1

Easy-change filter for CleanAir recirculation mod-

ule (can be regenerated)

Z50XXP0X0

CleanAir air recirculation module (can be inte-

grated)

Z51FXI0X5

Regeneratable CleanAir recirculation module (can 

be integrated) 

Z51FXJ0X5

Accessory - wide 345 mm

Order number

Starter set for air recirculation mode 
Easy-change filter for starter set

Z5102X5
Z5102X1

CleanAir recirculation module
Easy-change filter for CleanAir recirculation mod-

ule (cannot be regenerated)

Z5276X0
Z5170X1

Easy-change filter for CleanAir recirculation mod-

ule (can be regenerated)

Z50XXP0X0

CleanAir air recirculation module (can be inte-

grated)

Z51FXI0X5

Regeneratable CleanAir recirculation module (can 

be integrated) 

Z51FXJ0X5

Summary of Contents for D96BMU5N0A





















Reviews: