NEFF D95FQ Series, Manual

Page: 9 / 20

Cleaning and servicing
en
9
‒
To set the air recirculation mode (non-regener-
able filter), press or until appears on the
display.
‒
To set the air recirculation mode (regenerable fil-
ter), press or until appears on the display.
‒
To set the air extraction mode, press or until
appears on the display.
2. Release to save the setting.
7.25 Switching on the signal tone
Requirement: The appliance is switched on.
▶
Press and hold and at the same time for ap-
prox. three seconds until a signal sounds.
a
appears on the display.
7.26 Switching off the signal tone
Requirement: The appliance is switched on.
▶
Press and hold and at the same time for ap-
prox. three seconds until a signal sounds.
a
appears on the display.
8 Cleaning and servicing
To keep your appliance working efficiently for a long
time, it is important to clean and maintain it carefully.
8.1 Cleaning products
You can obtain suitable cleaning products from after-
sales service or the online shop.
WARNING ‒ Risk of electric shock!
An ingress of moisture can cause an electric shock.
▶
Before cleaning, pull out the mains plug or switch
off the fuse in the fuse box.
▶
Do not use steam- or high-pressure cleaners to
clean the appliance.
WARNING ‒ Risk of burns!
The appliance becomes hot during operation.
▶
Allow the appliance to cool down before cleaning.
ATTENTION!
Unsuitable cleaning products may damage the sur-
faces of the appliance.
▶
Do not use harsh or abrasive detergents.
▶
Do not use cleaning products with a high alcohol
content.
▶
Do not use hard scouring pads or cleaning
sponges.
▶
Only use glass cleaners, glass scrapers or stainless
steel care products if recommended in the cleaning
instructions for the relevant part.
▶
Wash sponge cloths thoroughly before use.
8.2 Cleaning the appliance
Clean the appliance as specified. This will ensure that
the different parts and surfaces of the appliance are
not damaged by incorrect cleaning or unsuitable clean-
ing products.
WARNING ‒ Risk of explosion!
Highly caustic alkaline or highly acidic cleaning agents
in conjunction with aluminium parts in the interior of the
appliance may cause explosions.
▶
Never use highly caustic alkaline or highly acidic
cleaning agents. In particular, do not use commer-
cial or industrial cleaning agents in conjunction with
aluminium parts, e.g. grease filter on extractor
hoods.
WARNING ‒ Risk of electric shock!
An ingress of moisture can cause an electric shock.
▶
Before cleaning, pull out the mains plug or switch
off the fuse in the fuse box.
▶
Do not use steam- or high-pressure cleaners to
clean the appliance.
WARNING ‒ Risk of burns!
The appliance becomes hot during operation.
▶
Allow the appliance to cool down before cleaning.
WARNING ‒ Risk of injury!
Components inside the appliance may have sharp
edges.
▶
Carefully clean the appliance interior.
1. Observe the information regarding the cleaning
agents.
→
"Cleaning products", Page 9
2. Clean as follows, depending on the surface:
‒
Clean stainless steel surfaces in the direction of
the finish using a sponge cloth and hot soapy
water.
‒
Clean painted surfaces using a damp sponge
cloth and hot soapy water.
‒
Clean aluminium using a soft cloth and glass
cleaner.
‒
Clean plastic using a soft cloth and glass
cleaner.
‒
Clean glass using a soft cloth and glass cleaner.
3.
Dry with a soft cloth.
4. Apply a thin layer of the stainless steel cleaning
product to stainless steel surfaces using a soft
cloth.
You can obtain stainless steel cleaning products
from the after-sales service or the online shop.
8.3 Cleaning controls and lights
WARNING ‒ Risk of electric shock!
Penetrating moisture may cause an electric shock.
▶
Do not use wet sponge cloths.
1.
Observe the information regarding the cleaning
agents.
→ "Cleaning products", Page 9
2. Clean using a damp sponge cloth and hot soapy
water.
3. Dry with a soft cloth.