NEFF C18FT28.0, User Manual And Installation Instructions

Page: 13 / 56

Basic operation
en
13
9.
Press to switch off the appliance after
30 minutes.
→
"Switching off the appliance", Page 13
10.
Allow the appliance to cool down.
11.
Clean the smooth surfaces with soapy water and a
dish cloth.
12.
Empty the water tank and dry the cooking compart-
ment.
→
"After every steam operation", Page 16
13.
Thoroughly clean any accessories you used with
soapy water and a dish cloth.
Note:
The appliance retains the calibration settings,
even in the event of a power cut or disconnection from
the mains.
Tip:
To ensure that the calibration settings are updated
to accommodate the conditions at the new location
when you move house, restore the appliance's factory
settings in the basic settings. Then repeat the calibra-
tion procedure.
→
"Basic settings", Page 24
7 Basic operation
7.1 Switching on the appliance
▶
Press to switch the appliance on.
Notes
¡
In the basic settings, you can specify whether the
heating functions or the main menu should appear
when you switch on the appliance.
→
"Basic settings", Page 24
¡
If you do not perform any actions on the appliance
for an extended period, it will automatically switch it-
self off.
7.2 Switching off the appliance
▶
Press to switch the appliance off.
Notes
¡
The residual heat indicator will appear on the dis-
play while the cooking compartment is still hot.
→
"Residual heat indicator", Page 13
¡
The cooling fan will continue to run until the cooking
compartment has cooled down.
→
"Cooling fan", Page 8
7.3 Residual heat indicator
After you have switched off the appliance, the residual
heat indicator will appear on the display.
Display Temperature
Residual heat high Over 120 °C
Residual heat low Between 60 and 120 °C
7.4 Setting the type of heating and
temperature
1.
Press to switch the appliance on.
a
The heating functions will then be displayed.
2.
Swipe left or right until the required heating function
appears in the middle.
3.
Press the temperature.
4.
Swipe left or right until the required temperature ap-
pears in the middle.
5.
Press to start.
a
The cooking time will appear on the display.
a
The heat-up indicator bar visualises the rising tem-
perature.
6.
When the food is ready, press to switch the appli-
ance off.
7.5 Changing the temperature
You can also change the temperature once you have
started the appliance.
1.
Press the temperature.
2.
Swipe left or right until the required temperature ap-
pears in the middle.
a
The temperature will now be changed.
7.6 Changing the type of heating
If you switch to a different heating function, the appli-
ance will reset all the settings.
1. Press to pause operation.
2.
Press the heating function.
3. Swipe left or right until the required heating function
appears in the middle.
4. Set the temperature and start the appliance.
7.7 Pausing operation
1.
Press ⁠.
2. Press again to resume operation.
7.8 Cancelling operation
Note:
Some functions, e.g. cleaning functions, cannot
be cancelled.
▶
Press and hold the button until the function that is
currently in progress is cancelled.
a
Operation will stop and all the settings will be reset.
a
The cooling fan will continue to run until the cooking
compartment has cooled down.
7.9 Viewing the current temperature
You can view the current temperature while the appli-
ance is heating up.
▶
Press ⁠.
a The temperature will be displayed for a few
seconds.
7.10 Displaying information
Requirement:
The button must be lit.
▶
Press ⁠.
a
The information will be displayed for a few seconds.