background image

FlexPAK 800/1000

EN

20

NOTE! 

Check that the supply voltage corresponds to the data on the machine plate of the 

unit, see figure 1, before connecting the unit to the mains supply.

NOTE! 

Control that TR1, see figure 5, item 2

,

 is connected to the correct voltage range.

NOTE! 

Always replace worn, faulty or defect electrical components with new original parts.

For the power circuit, control circuit and terminal connection diagrams, see the electrical 

diagrams that came with the unit.

5.6 

General requirements

The following items are minimum requirements to ensure the proper function and 

required level of protection with regards to equipment category, the EC directives and 

standards listed in 

‘Declaration of conformity’

:

• 

Take proper measures to avoid all types of electrical stray currents to and from the 

duct system and electrical wiring.

• 

Check that the input voltage and frequency to the unit are correct.

5.7 

Ground check measurement

Check that the unit is properly grounded after both the main installation and regular 

maintenance work. If a component is removed and refitted, ground connection is to be 

verified.

5.8 

Automatic bin emptying function

See the PLC settings Manual.

5.9 

Machining chips and swarf extraction

See the PLC settings Manual.

5.10 

Pneumatic filter cleaning valve

See the PLC settings Manual.

5.11 

Compressed air installation

WARNING! 

Risk of personal injury.

• 

Use ear protection and safety goggles.

• 

The compressed air valve is to be locked in the closed position during maintenance.

5.11.1  Requirements

NOTE! 

The specified air consumption of the unit is limited to the short operation of the 

cleaning valve.

NOTE! 

Take measures necessary to avoid water or humidity in the compressed air when 

the unit is installed in cold environments.

NOTE! 

If antifreeze additives are used, use them continuously. Once added, the removal of 

the antifreeze additive may cause the pneumatic components to malfunction.

Summary of Contents for FlexPAK 800



































Reviews: