background image

             

                            NEC Versa P520 Disassembly Manual                                       Page 32                             

 

Notice 

 
The information in this guide is subject to change without notice. 
 
This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in 
any form or by any means without prior written consent from NEC Computers International BV. 
 
 
NEC COMPUTERS INTERNATIONAL BV SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS 
OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING 
FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. 
 
 
Copyright © 2003 NEC Computers International BV. All rights reserved. 
 
[Category] is a trademark of NEC Computers International BV. 
The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks 
of their respective owners. 
 
 

Versa P520 Disassembly Manual 

Author: BENS_DAN 
First Edition: 

September 2003

Document Part Number:  
Version: 

2

.0 

 
NEC 
A division of NEC Computers International BV 

Summary of Contents for Versa P520

































Reviews: