NEC Versa 2000 Series Service And Reference Manual Download Page 59

Page: 59 / 82

Connect the AC adapter as follows:

Connect the adapter's DC cable to the power connector on the rear of the system.
Connect the other end to the AC adapter.

Figure Section 2-4 Connecting the AC Adapter

Connect one end of the AC power cable to the AC adapter. Connect the other end
of the AC power cable to a 100- to 240-volt, AC wall outlet.

Battery Power

It is highly recommended to use battery power only when an AC outlet is unavailable. A
fully charged battery pack lasts approximately 5.5 hours under maximum power save
mode, and 2.5 hours without power save mode.

The actual amount of battery time depends on the use of power-saving features, the
application, options installed, and the environment.

Refer to the Battery Status table in the LEDs section for information on determining how
much battery power is currently available.

Summary of Contents for Versa 2000 Series



















































































Search results

Summary of Contents for Versa 2000 Series

Reviews:

Related manuals for Versa 2000 Series

Brands by name

Popular brands

NEC Versa 2000 Series, Service And Reference Manual

Search results

Summary of Contents for Versa 2000 Series

Reviews:

Related manuals for Versa 2000 Series

Brands by name

Popular brands